Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Washer Vibration Sensor Assembly by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM16737933
Manufacturer Part Number: DC93-00278B

The Washer Vibration Sensor Assembly is essential for maintaining the stability and performance of your Samsung washer. This genuine OEM part accurately detects and manages the vibration levels during wash cycles, ensuring your machine operates smoothly and efficiently. By replacing a faulty sensor with this high-quality assembly, you can prevent excessive shaking and potential damage to your appliance. The Washer Vibration Sensor Assembly is designed to fit a wide range of Samsung washer models, guaranteeing a perfect match and straightforward installation. With its reliable performance, this sensor helps extend the lifespan of your washer, providing peace of mind and optimal functionality. Investing in this genuine OEM part ensures that your Samsung washer continues to deliver excellent washing results while minimizing noise and movement. Whether youGÇÖre troubleshooting an existing issue or aiming to enhance your washerGÇÖs performance, the Washer Vibration Sensor Assembly offers a dependable solution for a better laundry experience.

More
$93.49

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Samsung Washer Vibration Sensor Assembly (Part Number: OEM16737933)

1 Answer

Hello Deidre,
The fault code indicates an error with the MEMS Sensor. If the output from the MEMS sensor is over 4.5V or under 0.5V and it continues for 5 seconds, this error occurs. You will need to check the wire connector terminals between the MEMS sensor and PBA connector CN8. If no problem found, either the MEMS Sensor DC93-00278B or PBA DC92-01021V will need to be replaced.

Read More...

1 Answer

Charlene,

We are not showing a mems sensor on this unit. But if the unit had a mems sensor it would most likely be on the bottom of the tub.

Read More...
Kenneth G.Price for Model Number wa476dshawra1 0001

My washer at various times stops due to the 8e error code coming up on wash cycle,rinse cycle,and spin cycle most of the time it will like 4-5 minutes on spin cycle and clothes have to be wrung out by hand to put in dryer. I've replaced the orca controller,mems sensor and the display control board and problem still persist also sometimes it want even start to fill with water at start of wash,so if you can give any help I would appreciate it. Thanks

1 Answer

Kenneth,

You will want to test the wiring between the mems sensor and the control board as this is a mems sensor issue. If the wiring checks ok then the main control would be the most likely issue.

Read More...

1 Answer

Hello Jason. If the sensor is new and your still getting the code, you will need to order and replace the main board on the unit.

Read More...
Cory for Model Number samsung wa456DRHDSU/AA

The wire broke on the drain pump so I repaired it and reconnected it. turned the machine back on and now the pump works but now it won't turn off. checked the wires and they are in the correct spots. Also turned it off, unplugged it and pressed power again to drain the residual power and when I turned it back on the pump started up immediately. Tried a cycle and it eventually came up with error code nf (no fill) as the pump won't turn off. Don't know what it could be. Could something else have burnt out due to it trying to drain constantly? I didn't pull the cover off the mainboard but I do smell a burnt smell from around it.

1 Answer

Hello Cory. You will need to order and replace the main control board on the unit.

Read More...
Tony for Model Number WA5451ANW/XAA-0002

What does ASSY Sensor; Mems Sensor do? I am having (dc) error code problem with my Samsung WA5451ANW/XAA 02 top loading washer. I have just replaced all 4 suspension rods but the machine still won't complete the spinning cycle. The machine will continue to restart the rinsing cycle when it reaches the final 9 minutes mark. The machine is perfectly leveled, and the it doesn't vibrate so much to warrant a obvious concern. I am just wondering if there is a balance sensor that is sending false information. Thank you!!

1 Answer

Tony,


The Mems sensor is for unbalanced loads. With what you have changed then it is a good likelihood of the mems sensor being faulty.

Read More...

1 Answer

Gary,

With this issue of the unit working sometimes while hitting the start button then the most likely cause of failure would be in the user interface DC92-01311B.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google