Nizam Mohammed December 29, 2018 for Model Number Samsung Washer WA5451ANWXAA02 Getting DC on screen and have to restart and in spin mode , the time sometimes increases. you may just see the time jump from 5 to 12 minutes. Any assistance will be greatly appreciated. Thanks in advance
1 Answer Nizam, This error code DC is a unbalance error. Check the type of laundry. Check whether it may cause an unbalancedsituation.- Educate the consumer in this case, to presspause, reposition the load or remove a few items. Press start tocontinue and complete the wash cycle. Read More...
Randall November 04, 2018 for Model Number WA5471ABW/XAA Thanks for the help. When we start the wash cycle no water comes out. No hot or cold. The bucket will move as if it had water in it. Just no water. I see that there are several solenoid valves. I cant believe that all of them stopped working at the same time. do you think it is the control board?
1 Answer Randall, You will want to check the pressure hose and pressure dome on the side of the tub to make sure that they are not clogged up. If it is not blocked or clogged then you will want to check the pressure switch to make sure that it is reset to empty and if this checks ok then the issue will most likely be caused by the main control board. Read More...
Pedro October 11, 2018 for Model Number WF45H6300AG/A2-0000 I put my washer in a normal cycle and once I turn it on it locks the door and it tries to do a cycle but nothing happens. Then the door unlocks and error code 8E shows up. I tried doing a calibration on it and a soon as I tried to do it, it runs for about 10 seconds then error codes 8E1 shows up. Any suggestions?
1 Answer Hello Pedro, If there are no wiring harness issues present, you will need to replace the main control board DC92-01621A. Read More...
Dave September 15, 2018 for Model Number WA48H7400AW/A2-0000 I have the new MEM sensor in hand where is it on the machine ?
1 Answer Dave, This mems sensor should be located at the bottom of the tub on the right hand side of the unit. Read More...
Jenny August 13, 2018 for Model Number WA45M7050A I keep getting error code 8C. We just replaced the mems sensor and are still getting the code. We have checked all the connections and everything is tight. My washer is barely a year old and wont go into wash cycle at all, it just fills and drains over and over again.
1 Answer Jenny, Recheck and make sure the wiring connections are clean (no corrosion), tight and proper. Also check the connections and wires at the control board. If the problem persists, then the issue would be in the control board itself,the control isn't "seeing" the digital data from the sensor. Read More...
Mike July 29, 2018 Where is the mems sensor located? I have a WA5471ABP washing machine. I keep reading “the back panel” but I don’t think mine comes off. Is it under the machine? Also where is the wiring harness? I keep getting the 8E error.
1 Answer Mike, The MEMS/vibration sensor DC93-00278B / DC93-00278B Assy Sensor;mems Sensor, is located on the bottom of the outer tub. You will need to raise the front of the washer, or lay it on it's back to access it. The wiring harness is the 6 wire connector that "plugs" into the sensor and is routed up through the cabinet and control console and is "plugged" into the control board. You will need to check and make sure the connections are clean, good and fit tightly when plugged together. and make sure the connections at the control board are proper and tight. Read More...
Tim July 20, 2018 for Model Number Samsung washer model WA48j7700a When I start cycle the washer spins a few times as normal and then stops, drains and makes a continuous noise as if trying to fill with water. An 8C code has a appeared but the last few time the above issue occurs without showing a code. I replaced the inlet valve, checked hoses, drain hose height and at this point out of ideas.
1 Answer Hello Tim, The 8E error means there is a control board connection error. Make sure the wire harnesses from the main control board to the washer are secure. If so, this is normally an issue with the main board DC92-01021V. Read More...
Justin July 03, 2018 for Model Number WA52J8700AW/A2 The washer does not appear to be spinning normally as the clothes remain very wet when spin is complete. Several days ago we heard a loud grinding noise during a spin cycle but not sure what happened as we weren't in the room at the time. Now, when we run a wash and spin cycle, the clothes are extremely wet at the end of the spin cycle (the washer does spin). Also, it does not appear to be spinning as fast as normal. I have done some troubleshooting and am stuck... I removed the drain pump, cleaned it out (had a little bit of gunk) and verified resistance (normal). The drain pump appears to be working normally. I have run every washer diagnostic test and all pass. The spin test will spin up to 1032RPM without errors. What should I be checking next? There are no diagnostic error codes.
1 Answer Justin, With the unit not spinning properly and making a loud grinding noise you will first want to check the clutch assembly. If it is not damaged or faulty then the bearings would most likely be faulty and need replaced. Read More...
Don July 02, 2018 for Model Number WA48J7770AP/A2(02) I'm not getting any error codes. In demo mode I can get it to spin but in the wash (tumble) mode it shakes and stutters in both directions you hear high current, motor staining as if it has a high load but in the off mode everything moves freely.
1 Answer Don, This issue would most likely be a problem with the rotor, stator or the RPS sensor on the unit. You will want to put it into a diagnostics (if not done so) to see if there are error codes stored. If there are not it could be a wiring issue or possibly a main control board sending improper voltage to the stator and RPS sensor. Read More...
Kevin Whitcomb June 24, 2018 for Model Number WA48J7770AP/A2 Keep getting Code ur even when nothing in washer .Checked level and level is good. What could it be?
1 Answer Kevin, You didn't mention any abnormal noises, so we'll presume the clutch and motor are OK. You do want to check under the tub cover and make sure there aren't any small articles or debris between or under the tub. The DC93-00278B / DC93-00278B Assy Sensor;mems Sensor, is a good possibility, but it usually takes a "good" vibration or " tub hit" to make an error code to appear, but you do want to check and make sure the wiring is connected properly and tightly and check inside the plastic connectors for moisture, condensation and discoloration. Then check the motor RPS sensor and wiring DC31-00098A / DC31-00098A a false reading, loose connection, etc. could imitate an off balance load and cause the error code. Read More...