Michael January 07, 2022 for Model Number WA456DRHDSU/AA-0001 Our Samsung washer has started behaving strangely. When we start a wash cycle it fills for a bit, then pauses, then fills for a bit, then pauses, then fills. etc. It never seems to stop filing or actually start the agitation/wash part of the cycle. This happened once before and I found that the end of the pressure switch hose had come off the nipple on the side of the drum. I reattached the hose and clamped it on and the washer started working. This time I looked at that hose and it IS still connected, so I figured it was probably a bad water pressure switch. I replaced the original DC96-01703C with a new one and the washer is still doing the same thing. I tested both switches with a multimeter and got the same results from both: the two outside pins show ~23ohms of resistance, the center pin to either of the outside pin shows infinity. When I blow into the hose attached to the pressure switch I can hear the diaphragm moving, but the resistances do not change at all from any combination of the pins. Does this show that the old switch is bad AND the new switch is bad? Or are both good and something else is the problem? Thanks! Mike
1 Answer Hello Michael, the cause of the problem is similar to what you found before, As the washer fills with water the air pressure slowly builds up in the airline hose to the pressure switch, once satisfied the pressure switch tells the board to stop powering the water valves. If however, the air pressure drops the board thinks there is a load of heavy or cotton type clothes that absorbed the water and it tops it off with extra water again. Likey the there is a tiny crack/hole in the airline hose of the pressure switch diaphragm, the pressure switch /hose is part [AP5581361[. Also, check the drain hose is not too low is causing the wash water to siphon out. Read More...
Joe July 14, 2021 for Model Number Wf520abp/xaa Turn unit on and immediately throws water level pressure switch code. Replaced switch and hose. Cleaned filters. And still throws the code immediately. What is the next step to find what is wrong ?
1 Answer Joe, With the water level switch error still coming on after replacing the pressure switch and hose, this would be a main control board that would cause the issue. Read More...
Luis Cordova June 23, 2021 for Model Number WA45H7000AP/A2 My Samsung VRT washing machine keeps pumping water into the drum nonstop. I get a 4E error message indicating a problem with the water supply. I'm not so sure. Others had suggested it might be a faulty pressure sensor so I bought a new one. However, both the old and new sensors behave the same way. There is no continuity between terminal 1 and 2 and between 2 and 3. The resistance between 1 and 3 seems to be about 23 Ohms. Blowing into the tube seems to make no difference in any of these measurements. Are both my pressure sensors bad?
1 Answer Luis, Check to make sure that the screens on the water valve is not clogged up and if it is not then it is possible that the valve is faulty and would need to be replaced. Read More...
Eddy February 24, 2021 for Model Number WF42H5000AW/A2 01 First I want to thank you for your reply. Follow up question. I checked the pressure switch and found out the hose was rubbing against the drum and its cutting through it. We need to replace it. How am it going to get into it? Some brand have it easy access at the back but this one I think need to open the front panel? And I’m afraid to start get the screws out. Thank you again
1 Answer Eddy, the pressure hose would be easier to access through the front panel as this will allow the most room to access the clamps. Read More...
Eddy February 23, 2021 for Model Number WF42H5000AW/A2 01 Hello. Washer runs at first then around middle of the cycle will automatically drains and display LE error. The drains pipe has not moved since we got this washing maybe 4 yrs ago? And I checked the filter and nothing is in it. Can pressure level switch cause this? How to check? Thank you very much
1 Answer Hello Eddy, You need to check the water level sensor hose for clogs, kinks, damage, or disconnection. There could be an issue with the water level sensor DC96-01703Q but as per the information we have from the manufacturer, it is more likely to have a main control board DC92-01803D issue. Read More...
Bill January 24, 2021 for Model Number WA400PJHDWR/AA-0001 Durrng cycle start it seems to agitate for about 30 seconds with water flow, then the drum slowly turns for about 5 min. with no water flow, then it shuts down and gives the nf code. will a new water level switch take care of this problem?
1 Answer Bill, You will want to check the screens on the water valve and make sure that they are clean. If the screens are dirty then clean them and see if this does not correct the issue. If the screens are clean then the issue will most likely be caused by either a clogged pressure hose or a pressure switch that is faulty. Read More...
Mark January 14, 2021 for Model Number WA45H7000AW/A2-02 Water continues to fill. Replaced pressure switch and the machine continues to do the same thing. Does this on all cycles. Emptied machine and tried to do a calibration - seemed to do what it was supposed to but did not help with the continued fill. Any suggestions?
1 Answer Andy, For this issue, the most likely cause for this will be a faulty main control board sending power continuously to the water valve. Read More...
Kevin September 02, 2020 for Model Number WF337AAG/XAA Unit will not drain. Pump was bad one year ago and replacing it solved the drain issue. Now one year later, it stopped draining again so I ordered a drain pump and replaced it although I saw no trauma to the impeller like the first time, however, after replacing the drain pump, in one quick test mode, the drain pump activated when I pressed the soil level button so I called it fixed and assembled. Ran a wash and same thing happened, get an "ND" and a persistent F21. When I enter the quick test, the soil button does not turn on the pump. There is no voltage at the connector for the pump when I try to activate the drain pump in quick test mode and there is a persistent F21 code. When I check terminals 1 & 3 I have a reading of 25.6 ohms at all times and does not change when I blow into the vacuum nipple. Is this pressure switch my cause?
1 Answer Kevin, if the drain pump is not showing 120VAC at the contacts during a drain portion of a cycle, the failure would be at the main control MFS-WF327L-T0. While the pressure switch would affect water filling or not sensing if the water has drained out, it would not cause the drain pump to not activate. Unfortunately, the main control has been discontinued by the manufacturer and is no longer available. Read More...
Richard May 13, 2019 for Model Number WA45H7000AP/A2 would the water level fill up and then empty if the water pressure switch is bad. what should i look for?
1 Answer Richard, Normally, no the water level/pressure switch, would not cause the symptoms you described. First check the drain hose and drain pipe, make sure the top of the pipe is 38" up from the floor, the hose isn't pushed too far down in the pipe, these issues can cause a "siphoning" issue and produce the issues you describe. Wouldn't expect the drain pump or the control board to be a problem at this point. Read More...
Delita October 31, 2018 for Model Number WA45H7000AW If the hose to the water pressure valve is off at the bottom of the tub will it leak water? I was having a water leak and when I took the back off the frame the end of the hose that attached to the drum was off. Model #WA45H7000AW Samsung
1 Answer Delita, if the pressure hose comes off of the air dome on the outer tub it most certainly will leak water when it tries to fill. You need to re-attach the hose and make sure it is secured or else it will come off again. Read More...