Tammy September 24, 2014 for Model Number RB1955SH Unit not holding temp. Fridge would have to be unplugged and rebooted to cool back down. I have replaced sensors and main control board. I have felt the compressor-as mentioned on another thread-and not hot to the touch. Temp is reading -14/34, but not that cold in there after using thermometer to check temp. Cannot figure out problem. Should I have reset the temp control after installing main control board? Any help is appreciated.
1 Answer Tammy, You will want to check the frost patterns on the evaporator coils to see what the frost pattern looks like. It is possible that there could be a leak in the sealed system that would cause the unit to not get cold enough and if it is just one side not getting cold enough could be that it is not defrosting. Read More...
Ken December 26, 2013 for Model Number Samsung RB 215LASH Compersor MK 172c-l2u; Bom name RB215 lash/xaa My refrigerator and freezer quit running. The condensor comes on and the fan as well. I took the inside panel for the freezer & refrigerator section and noticed the fans are working. One tube from the condensor was all white but not frozen over--I think...so I used a blow dryer on it. After I put everything back, the refrig. & freeze started to work for a few hours then again back to not workings. Now the electronic display panel does not work only displays a couple of lines. Every few hours, the refrig. & freezer seem to work but then not. I placed water in ther freezer and it freezes and then thaws out. Please help
1 Answer Hello Ken. If one tube was frosted, and the rest were clear, you have a sealed system issue and will need and HVAC tech on the unit. Read More...
Gettin Warmer October 24, 2013 for Model Number samsung rb2155sh Our refrigerator has stopped cooling. The freezer maintains the temp it's set at. I noticed that when I unplugged it and plugged it in that the light in the refer section goes out after a short time. I have replaced the main control board but it made no difference. Any suggestions?
1 Answer Hello. Look at the back wall inside the fresh food and see if it is frosted over. If so, then it sounds like the fresh food will need the evaporator assembly DA96-00017C replaced. Read More...
Roland July 03, 2013 for Model Number Samsung RB2155SH Hello Again, Unfortunately after replacing the thermistor and the Control Board, my refrigerator continues to need re-booting to maintain temperature. The refrigerator compartment reaches the programmed temperature (34 degrees) but the freezer never gets cooler than (19 degrees). I can hear the motor running when I place my ear to the unit, so I'm not sure what is going on. Thanks
1 Answer Hello Roland, You should pull the unit out from the wall and make sure the fan and the compressor is running. If the unit won't kick back on after the temperature is satisfied, most of the time the issue is a bad relay on the main board. If this is not the case, (since you mentioned the main boards' replacement), the issue could be the start relay on the compressor. If the compressor is running hot, (too hot to hold your hand to), the sealed system could have a restriction that is causing the compressor to trip the overload. Read More...
Roland June 26, 2013 for Model Number Samsung RB2155SH I recently posted a question regarding my refrigerator that is not maintaining temperature. Like other folks who posted here, I need to re-boot the unit by unplugging/re-plugging it. This starts the motor, cools to the programmed temp then stops cooling. I Just ordered and replaced the temperature sensor DA32-10105T hoping it would be a quick fix but to no avail. Now I just ordered a main control board AP4141488 (DA41-00128D). Please advise on how to reach this part. I can't see anything other than a diagram on this site and it's a little confusing to me visualizing the access to this piece. I s this something for a DIY'er or should I call a pro? Do you think there may be another part or sensor that may be the problem? Thanks for your help!
1 Answer Hello Roland. You need to order and replace the main control board in the unit. Read More...
Deb June 12, 2013 for Model Number RB1844SW Our Refrigerator and microwave are on the same circuit breaker which is 30 amp but are not plugged in to the same plug. When I do something in the microwave the refrigerator goes off and I have to unplug it to restart it. Does this mean something is wrong with the refrigerator or the wiring?
1 Answer Hello Deb, The issue is the wiring in your home. If you check with the installation or owners guide on both the refrigerator and microwave, you will find that both units are required by the manufacturer to be on a dedicated breaker. Putting in an oversized breaker will cause a fire hazard so that is not an option. The only option is to have a separate circuit run to the refrigerator and microwave so it will be a safe, reliable installation. Read More...
Theo April 20, 2013 for Model Number Samsung rb1955sh The temperature of both the freezer and refrigerator rises yet the display does not indicate the rise in temperature. I have to recycle the power to both see what the actual temperature is, and to get it to start cooling down again. Thanks.
1 Answer Theo, Based on the information it sounds as though the unit may be getting stuck in defrost which would require a new main control board. You will want to check to see if the fans are operational at the time that the unit is not working. If the fans are not running this would most likely confirm being stuck in defrost. Read More...
1 Answer Hello Terry, I'm sorry but, we do not at this time have the ability to ship outside the continental United States. Read More...
Don F. October 23, 2012 for Model Number Samsung RB1955sw The child lock is on and i can not get it to turn off. I can not adjust the temps. I have replaced the touch control and still has the same issue. The key procedure for turning on and off the child lock does not work. It stays on all the time. the only other control device on the unit is the main PCB. could this be the issue?
1 Answer Hello Don, The first thing that I would recommend is to double check your control board to ensure that none of the buttons are wedged and depressed. This will cause an override and cause child lock to come on. If this checks good then you would need to replace main board DA41-00128D. Read More...