Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Refrigerator Main Control Board by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM12424473
Manufacturer Part Number: DA41-00128D

Fridge won't cool or displays blinking error codes? The main control board regulates temperature and defrost cycles. Moderately difficult repair.

More
$200.95

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Samsung Refrigerator Main Control Board (Part Number: OEM12424473)

1 Answer

Hi. Are both door gaskets sealing properly? Are you hearing both the condenser fan motor part # DA31-00010B and the evaporator motor part # DA31-00002V running? IF the condenser fan does not remove the compressor freon heat then it will boil the freon and not allow the evaporator to frost over - creating hot freezer temperatures. If the fresh food evaporator motor part # DA31-00003N does not turn then the freezer air will not circulate supplied air quality. Double check all main board part # DA41-00128D connections for tight pin connections individually.Thank You.

Read More...

1 Answer

Hello Victor. If the control board is new and the wires are connected properly, you may have a bad temperature sensor DA32-10105T in the unit and it is not reading that the unit needs to be turned back on to keep cool. It should read around 5500 ohms at room temperature. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Read More...

1 Answer

Hello Wally. This is an indication of a defective power supply on the board DA41-00128D. Unfortunately, this can only be repaired by board replacement. Hope this helped!

Read More...

1 Answer

Hello Sam. The assembly is what is discontinued. You can test the thermistors and see if they are bad. Thermistor
Temperature Resistance
77°F..................10,000 ohms
36°F..................29,500 ohms
0°F....................86,300 ohms
If they test bad, you will need to replace them. If they test good, then there is no need to replace them. This will determine which thermistor is bad in the unit. They are not hard to replace. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html

Read More...
Sam for Model Number RB1955SW

Thank you for the response regarding the error code 00 0. So I can decide if it is cost effective how much is the assembly number-ap4168192? Is there an assembly for the freezer parts you mention or do I buy them separately as listed?Also you listed the thermistors twice for each compartment and they are the same part numbers. Do I buy two of AP4136048 and two of AP4136842 or one pair for the freezer and then the assembly will come with a pair? Is the replacement for everything you mention "easy" for a DIY'er? If I replace the assembly in the fridge will I still need to replace the AP4138824 thermistor? In response to you question, no there is no frost on the back wall of the freezer.

1 Answer

Hello Sam. DA97-00459H has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Thanks.

Read More...
Sam for Model Number Samsung RB1955SW

Code shows 00 0 after pressing power freeze and power cool simultaneously. Refrigerator and freezer both cool/freeze to 38 and -2 from room temperature in about two hours after being unplugged and replugged. Then after about 12 hours the readings for refrigerator fluctuate and the refrigerator is not cold but the freezer stays at -2. No visible signs of ice build-up in either compartment. When it failed initially there was water under the crisper drawers and the drain pain had about 3 inches of water but has not done that since the first failure. Relay and compressor readings seem correct, but relay reads 146V not 120V. Coils are clean and fan near compressor runs, copper lines frost and defrost and I can hear the coolant flowing from the compressor. I have not checked AP4136842 or AP41360048 because I did not want to disassemble the interior if you think it is the main control board AP4141488. Should I replace the control board and both sensors or just the sensors or just the board? How can I be sure it is not the refrigerator or freezer evaporator fan motors?

1 Answer

Hi Sam. You can open each compartment and hear or feel the back center wall to see if the fans are running. However it is common to replace the whole assy. since it has been updated and you take a chance in breaking the styrofoam insulation that surrounds each component. In the freezer bottom mount, there are 2- different thermisters that supply the control board. They are part # DA47-00095E and part # DA32-10105R. Is there any frost on the back wall ? The freezer fan is part # DA31-00002V. Now for the fridge side... There are 2 thermisters part # DA32-10105R and DA47-00095E. They also are mounted on top of the evaporator. They have been upgraded. The fresh food fan is part # DA31-00003N. Or you can buy the whole assy. w/ back cover part # DA97-00459H. It is currently out of stock but we restock each week. There also is a front thermister to the left of the fan blade part # DA32-10105T behind the front cover. The 00 0 indicates a door switch defective part # DA34-00006C. Thank You.

Read More...
Zed for Model Number RB1855SL Canadian Model

After power failure fridge stopped to work. On the front display only one "8" line on 4th digit is blinking, nothing else. Reset power a few times, did not help. Suddenly after 3-4 days everything come back in normal by itself?! Worked for a month and than again power failure happened and we came back to square one. The same situation, fridge does not work, on the front display only one "8" line on 4th digit is blinking. Is this Main Control Board problem?

1 Answer

Hi Zed. It does sound like the main control board has an intermittent issue. Part # DA41-00128D.You will need to pull the refrigerator out and unplug the unit. Remove the cover over the compressor compartment and remove the control board housing. Remove the screws holding the housing together to access the control board. Then unplug the wires going to the old control board and remove the old board. Reinstall in reverse order. Thank You.

Read More...

1 Answer

Hello Terry. You will need to pull the refrigerator out and unplug the unit. Remove the cover over the compressor compartment and remove the control board housing. Remove the screws holding the housing together to access the control board. Then unplug the wires going to the old control board and remove the old board. Reinstall in reverse order. Hope this helps.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google