Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Refrigerator Compressor Overload Protector by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM13004352
Manufacturer Part Number: DA34-00004D

Refrigerator compressor won't start after power surge? This overload protector prevents electrical damage to your compressor. DIY repair in 30 minutes.

More
$47.95

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Samsung Refrigerator Compressor Overload Protector (Part Number: OEM13004352)

1 Answer

Roberto, thanks for the question.
Check to ensure the compressor is running when power is applied.

Read More...

1 Answer

Roberto, thank you for the question.
Here is a link to: Refrigerator not cooling: Common Causes & How to Fix: https://www.appliancepartspros.com/repair-help/refrigerator-repair-help/refrigerator-not-cooling.html
and to other repair help: https://www.appliancepartspros.com/repair-help/

Read More...

1 Answer

Hello Ken, and thank you for your question. The refrigerator and the flex zone thermistors would need to be tested for resistance to identify if they are operating properly. At 37 degrees they should measure around 11,700 Ohms and at 65 degrees, they should measure around 6500 Ohms. If the thermistors test good for resistance, the main control would be the likely cause of failure based on the information provided. For the most accurate part information, the REV number of your appliance would be needed.

Read More...
Cafweiss for Model Number RF28HFEDTSR/AA

The bottom ice bin compartment - something got stuck and was unable to open/close the bottom freezer compartment. When I reopen the door in the reserve ice bin there was a 6" curve plastic piece laying in the ice cube bin. Was not sure what the piece was too until the ice bin kept making ice over the next few days overflowing the compartment. So, my thought process, it must be the lever that stops ice from falling from above once it reaches a full status. So is there a part i can replace or is there a more serious piece that needs to be replace.

1 Answer

Cam,

It sounds like the compressor is fine and if the compressor is not running then it would be the inverter board which would be the smaller of the 2 boards.

Read More...

1 Answer

Cam, the inverter would be built into the main control and the voltage output would be a variable output. If the REV number of the appliance could be provided in a new question, this will allow the correct control to be identified.

Read More...

1 Answer

CAM,
The five blinks mean that the board thinks the compressor is locked up and won't turn over. The recommendation is to replace the inverter PCB and if your issue returns replace the compressor.
(replacement of the compressor would be a sealed system repair requiring an EPA-certified technician).

Read More...

1 Answer

Walt,

This cover gets pried off. There should be a tab that you would get a flatblade screwdriver and slide it in. Once you do this pry up and swivel it off.

Read More...

1 Answer

Gjepsen, the LED on the control blinking 4 times is going to indicate that the compressor MKV190CL2B/ASH is locked up. Unfortunately, this would require an EPA-certified technician to repair.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google