Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Refrigerator Compressor Overload Protector by Samsung

Best Seller
Manufacturer Part
4.89 (64)
By: Samsung
Part Number: OEM13004352
Manufacturer Part Number: DA34-00004D

Refrigerator compressor won't start after power surge? This overload protector prevents electrical damage to your compressor. DIY repair in 30 minutes.

More
$47.95

IN STOCK
Ships Tomorrow Guaranteed
Add to Cart

Questions & Answers

For Samsung Refrigerator Compressor Overload Protector (Part Number: OEM13004352)

Rmickens40 for Model Number RF261BEAESP/AA

I have a Samsung refrigerator French door bottom freezer, problem started when water started coming from bottom of crisper shelf, removed back panel unstop drain, went to back of fridge and remove bottom panel clean out two drain holes also removed dust from coils and fan, placed everything back together reset fridge back freezer temp not working properly and the ice maker do not work what is the problem with the unit. Will not freeze water bottle.

1 Answer

Rmickens40,

If the freezer is not cooling properly, you will want to make sure that nothing became dislodged when you where cleaning and if not then it sounds like you may have a sealed system type of issue.

Read More...

1 Answer

Hello QIn, your ref uses a variable speed compressor powered by an inverter board, that is next to the main control board, there is no start relay used, on the inverter board is a red LED,if there is a problem the LED will flash the fault code identifying the problem, when the compressor stops and it should be running, access the inverter board and count the flashes, repost your question with the number of flashes.

Read More...

1 Answer

Richy,

This unit does not have a start device that plugs into the side of the compressor. This unit uses an inverter board to operate the compressor. The part number for the inverter board would be DA41-00614B. You can look on the inverter board as well and there should be a part number on it. Since this board is showing discontinued make sure that it matches the one on your board.

Read More...

1 Answer

Hello Daniel,
The manufacturer advises that a refrigerator should not be on a GFI. The GFI is a quick trip breaker in case a mixer, hairdryer, etc. should be dropped into the water to prevent electrocution. Since it is doubtful that the refrigerator would ever be dropped into the water, connecting it to the power supply at an outlet not wired in series with a GFI should correct the issue. If it still trips the breaker in the breaker box, check the unit for components shorted to chassis ground.

Read More...
Ken for Model Number rfg297aawp

Fridge and freezer not cooling. the unit is about 10 years young. the invertor board led is solid red. no error codes on self diagnosis (start up or manual) the compressor starts up with power and is vibrating (running) the compressor fan is on I have removed internal covers and found no ice build up / left the unit unplugged for 24 hours to ensure full defrost. I have tried FF (fast cooling / fast freezing) but no luck. could it be a coolant leak? is my fridge truly "dead" please help if you can, love this unit but cant spend the same amount again on a new one.

1 Answer

Ken,

With the unit having no frost when the compressor is running, this would be a sealed system leak and you would need to have service to repair the unit.

Read More...

1 Answer

Elizabeth,

Unfortunately, the manufacturer is not listing the overload for your unit on the parts list. If the overload that you found looks like the one that you have then it should work for the unit.

Read More...
Agent797 for Model Number RF28M9580SG/AA-00

My samsung isn't cooling at all. Seems like stuck on defrost mode. I`ve replaced the overload relay switch, 2 temp sensors, defrost thermal fuse in freezer compartment and replaced the inverter board and still not cooling. The only piece I question is the overload relay because it came in a bubble envelope and it seemed to rattle like the one it was replacing. All fans work. The compressor kicks in and I can hear the clicks and it revving up but still not cooling the entire fridge. Tested the compressor windings and got 8.4ohms on all 3 which my understanding is since it's a 3 stage compressor that all 3 readings should be equal. At this point I am leaning towards a bad compressor but thinking of ordering new overload relay before going in that direction. Any ideas as to which direction I should go?

1 Answer

Agent797,
Based on the information provided if the compressor is running then the overload is not the issue. It sounds like from your description that you could have a compressor that is not pumping or a sealed system leak. These repairs require an EPA-certified technician.

Read More...

1 Answer

Ralph,
Based on the information provided I would advise placing the unit into the self-diagnostic mode and check for any stored fault codes and proceed with the diagnostics from there.

Read More...

1 Answer

Nick, it would be recommended that the refrigerator section evaporator cover is removed to identify if there is a no defrost issue. This can be identified by an excessive amount of ice blocking the airflow through the evaporator. If this has occurred, the defrost sensor DA32-10104N would need to be tested and it should measure more than 20KO if it is encased in ice. If it measures ok, then the failure would likely be in the main control DA92-00606E not allowing the refrigerator to defrost.

Read More...
Tom for Model Number kenmore 596.75522400

My compressor tripped on what I assume was thermal overload. I cleaned the very dirty coils from the front side and pulled it out from the wall niche, left it running. By the next morning, all was working well. I slid it back into niche, and next day compressor was tripped again. This time I left it out from the wall, and placed a small fan blowing into back directly at compressor. Have had no other trips. I want to push it back into niche without the fan blowing on it. TWO QUESTIONS: after the first trip, is there a reason the TOL would be more sensitive, maybe tripping at a lower temp? And do I need to really clean the coils from back panel until they're squeaky clean? Or, could there be a deeper problem I'm missing. The installed fan is running, I assume properly, although blades are a little dirty.

1 Answer

Tom,

You will want to make sure that the condenser fan is operational because if it is not then the Thermal overload will trip. The fact that the fan is blowing across it would indicate not enough air flow causing this issue.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google