Vickie November 30, 2019 for Model Number ECS130SCH Dacor electric oven I had a problem with one of the elements not working (took too long to heat up). The element did not test as an open circuit - tested at about 40 Ohms. It was suggested that the relay circuit board needed replacement - which I just did. Now, none of the elements work although I can hear the relays switching when asked to do bake, convection bake, and pure convection. What else could be wrong?
1 Answer Vickie, It would be recommended to check to make sure that everything is wired correctly on the control board. If it is then making sure that the element is getting power to it. If there is power to the element but not heating then this would be a faulty element otherwise it would be a faulty control board. Read More...
Vickie November 15, 2019 for Model Number Dacor ERD36 Hello. thank you for answering my last question about the spark igniters You said: "Hello Vicki, the ignition of the top burner is not controlled by the control board or switch membrane, you may want to recheck the wiring connections at the top burner gas valves igniter switches and the ends of the wire harness for it, it sounds like you have just a loose connection on the wiring." Where will I find the igniter switches and the ends of the wiring harness. Can I access them by just taking the front control panel off in the front that I did to replace the membrane?
1 Answer Hello Vickie,you will need to disassemble the burners from the cooktop, release the cooktop as the ignitor switches, wiring and spark module are all under the cooktop, just removing the front manifold will not give you enough access for checks. Read More...
Vickie November 12, 2019 for Model Number Dacor ERD36 Hi I have a DACOR range - congestion electric oven and gas cooktop - model ERD36 (we use propane). Recently, we got a fault indicating that we needed to replace the membrane, which we just did. Everything works EXCEPT that now the spark igniter for the burners does not work. The igniter was previously working, even without the membrane. What might now be wrong?
1 Answer Hello Vicki,the ignition of the top burner is not controlled by the control board or switch membrane, you may want to recheck the wiring connections at the top burner gas valves igniter switches and the ends of the wire harness for it, it sounds like you have just a loose connection on the wiring. Read More...
Vickie November 09, 2019 for Model Number Dacor ECS130SCH Where is the thermal fuse located? Is it accessible without taking the oven out of the wall?
1 Answer Vickie, The thermal fuse for this unit would be located on the back of the wall oven and would need to be removed from the cabinet to access it. Read More...
Vickie November 09, 2019 for Model Number Dacor ECS130SCH I have a dacor wall oven that took a long time getting up to heat, and suspect the lower element. I took out both the lower element and the broil element. They both test at ~25 ohms. I checked for voltage at the convection, broil and lower elements. Voltage good at both convection and broil. No voltage detected at lower element when set to 'bake' setting. Is there a fuse somewhere? If so, how to I get to that? Or is something else wrong?
1 Answer Vickie, This issue would more likely be a faulty relay control board with the bake portion not working. Read More...
Vince January 28, 2019 for Model Number Dacor ERD30S06CH The bake element in my Dacor ERD30 is broken. I understand 62628 is the one, but it's hard to find since it's discontinued. Is there any other baker element that will fit?
1 Answer Vince, due to the resistance values that vary from element to element, a substitute can not be recommended. The manufacturer will normally allocate a substitute part number if there is one available and there is not one for this model. Read More...
Louise October 02, 2018 for Model Number Dacor single wall oven PCS130 I'm looking for a replacement bottom heating/bake element. Do you have one?
1 Answer Louise, The part number for the Element is DE81-06277A but unfortunately we do not carry this part. Read More...
Jim March 31, 2018 for Model Number ECS230SBK Recently after using broiler in upper oven neither the bake or broiler function work the lower oven works fine?
1 Answer Jim, For this issue the most likely cause will be a faulty relay control board which is part number DE81-08448A. Read More...
Monica February 26, 2017 for Model Number Ecs130sch The broiler stopped working after it was cleaned. Then we noticed it was taking a long time to reach baking temps. Now the baking element has stopped working as well. After looking online we tried to reset the thermal fuse. It is still not working. Would the next step be to replace the thermal fuse?
1 Answer Monica, Test the thermal fuse for continuity. If there is no continuity then replace the thermal fuse. If the thermal fuse checks ok then the most likely cause for this issue will be the relay control board which is part number DE81-09179A. Read More...
Keith February 20, 2017 for Model Number Dacor ECS127SCH I have a Dacor oven, part number ECS127SCH, and only the broiler element is working. The required voltage is getting to the broiler element, but no voltage is registered at the bake or convection elements. Both the bake and convection elements have resistance above 19 ohms. How can I determine if I need a control board or relay board?
1 Answer Keith, This issue would be caused by a relay board which would have the relay for the bake and the convection are located. The part number for the relay board is DE81-09179A. Read More...