John February 11, 2015 for Model Number AGQB6400FS0 My dryer was spinning for more than an hour without heat. The display was dark with no error messages. The controls do not respond to any changes even though all the options show available while the previous cycle is running. I unplugged the unit hoping to reset however the unit continued its previous cycle even when holding the clear button. The heat did come on for a minute and the drum continues to spin. Hoping just a control board?
1 Answer John, Based on this information it does sound like the issue will end up being caused by a faulty control board. Read More...
Roy Smith October 28, 2014 for Model Number AEQ8000FE0 All the lights on my dryer light up on thier own and the 1:00 hour time stays lit on the display next a slow beep starts which gets louder and faster over time, if I unplug the dryer for a while it clears the display and lights but only for a short time. Today the dry will start but only runs a few minutes then stops. What do I need to replace?
1 Answer Roy, Based on the description of the problem it sounds like the issue would be with the control board. This sounds like a key that may be stuck or the board being corrupted. You would want to replace the control board part number 134557200NH. Read More...
David October 04, 2014 for Model Number AEQ6000ES2 Dryer will not heat. I can unplug it for 2 hours or so then it will work fine for a few loads. Then I have to do it again. Could this be the control panel?
1 Answer David, When the unit stops working you will want to check the thermostats to make sure that they are showing continuity. If they check ok then the control would be the most likely cause for the issue. Read More...
Vern P September 07, 2014 for Model Number AP3886716 Can't seem to get the last 2 connenctors(the ones behind the dial selector) loose from. Any professional suggestions?
1 Answer Hello Vern. The connectors have locking tabs on them. You press on the locking tabs to release them and pull the connectors off of the control board. Read More...
Gio July 27, 2014 for Model Number AEQ7000ES1 Hi, I'm not getting 12v to heater relay is there a fuse or some thing I can check.
1 Answer Gio, With the unit not heating you will want to check the thermal fuse and the high limit thermostat to make sure that they are working. If they check ok and you are not getting 120 vac to the heater relay then the issue will be a faulty control board. Read More...
Phillip July 02, 2014 for Model Number AEQ8000FEO Dryer shuts off after a few seconds. Each time I press start the dryer would shut off after a few seconds. Sometime FLd or ro8 shows in the display. What could be the problem? Thanks
1 Answer Hello Phillip, Fld is the indication that the control board is in the Field test mode and r08 is reflecting the firmware revision number. You will need to press and hold the select and cancel buttons simultaneously for 6 seconds to take the board out of this mode. Read More...
Chris June 13, 2014 for Model Number LEQ7000ESO The timer function on my control board is timing out sooner than the selection entered. Example would be 1 hour selected and dryer finishes cycle in less than 30 minutes with clothes still damp. Have tried other cycle settings and same thing occurs, cycle ends sooner than selected setting with dryer showing no time left on the clock. Is this a control board replacement for a bad timer? Thanks, Chris
1 Answer Chris, You will want to check the control thermistor on the blower housing to make sure that it reads 50K ohms at room temp. If not then the thermistor is bad and would need to be replaced. If the thermistor checks ok then the control board would most likely be the cause of failure. Read More...
Jose May 14, 2014 for Model Number part 134557200 This parts work in gas and electric dryers. Mine is electric but the part say gas?
1 Answer Jose, the control board 134557200NH can be used in electric or gas units. Thanks. Read More...
Peter May 08, 2014 for Model Number aeq8000fs Our dryer gets very hot, even when on air fluff. Works ok otherwise but after a 15 minutes of running starts to make whirring noise which goes away after it cools down. Replaced thermostat but no help there. Stuck relay? Control board? Thanks
1 Answer Hello Peter, If your wiring harness is not shorted and the heating element is not broken and contacting ground, the issue will have to be the electronic control board. The noise will be either the rear bearing, the idler pulley, or the front glides getting too hot. Read More...
Wayne March 31, 2014 for Model Number AGQ8000FS2 I can't find a control board with the serial number my board has on it which is 134556902. Which one should it be? Thanks.
1 Answer Wayne, the control board listed for the given model is part number 134557200NH. Thanks! Read More...