Junior January 02, 2019 I replaced the heater vent on Electrolux dryer, it was burning my clothes. Now the dryer will not turn on it looks like it’s in the sleep mode and can not wake it up. I’ve tried opening and closing door, unplugging unit, etc. I’m thinking the control panel went out, any suggestions?
1 Answer Junior, We will need to have the model number of your dryer to be able to assist properly with your question. Please provide model and resubmit your question. Read More...
Hector December 28, 2018 for Model Number saeq7000fso hello, my dryer is stopping every 5 minutes after it starts, i wiil like to know if by changing the control board this will stop. And if this is the correct control board for this machine. thank you for your time, hector echenagucia
1 Answer Hector, You will want to check the bearings and the bearing slides on this unit to make sure that they are not damaged as this can cause a drag on the motor causing it to shut off. Read More...
Me September 11, 2018 for Model Number AGQ8000FS1 How do you get the old control board off and put the new one on.?
1 Answer Me, To remove the control panel from this unit you will need to remove the 2 screws at the back of the unit holding on the main top. Once you do this slide the main top backwards and it should lift off. Then there will be some screws on the control panel holding it in place. Remove the screws and you will be able to get the panel off. Read More...
Steve W June 13, 2018 for Model Number LEQ2152ES0 I got the E68 error code - bad switch. Ran the diags and it's the dryness switch that is faulty. Can individual switches be ordered or do you have a part number for one? I have been an electronics tech for 40 years and know how to solder. I just don't want to waste any time opening the unit up if I can't replace the switch, as I don't think that spending $200 on a 12-year-old dryer is a great idea... Thanks!
1 Answer Steve, Unfortunately we do not have switches for the control board on the unit and unless you can locate one at an electronics store then you would need to replace the control board. Read More...
Annie April 20, 2018 for Model Number GLEQ2152ES0 E68 error code. Assuming I need a new control panel. Want to make sure I’m ordering the right part. Please confirm. Thanks.
1 Answer Annie, For this issue the part number for the control board will be 134523200NH. Read More...
Gary K August 27, 2017 for Model Number EL1346012 The dryer flashes a E68 code but no buttons appear to be stuck, we tried the test mode which seemed to function but out of sequence. Based on several questions and answers from your site, it would appear that we should replace the control board. The problem is that the Data sticker with model and serial number has faded completely to white. The number I have referenced in the Appliance Model Number field is the actual number on the control board. Any help is appreciated.
1 Answer Gary, Unfortunately the number listed will not allow us to pull up any part number because this would just be a number the manufacturer uses in its manufacturing process. This does sound likely that the control board would be faulty. Read More...
1 Answer Hello Julie. This code appears when you replace the user interface control or electronic control board using the wrong part. Use your dryer model number to check the part number for the replacement part. Unplug the dryer and install the correct part for your model. Read More...
Zim August 24, 2016 for Model Number ACQ6000ES0 I am getting an E68 error code and from reading the other posts I am assuming my control board is fried. I have done all there was to try and clear up the error but the dryer stays on less than a minute and then stops and flashes the code. Please tell me which control board I am supposed to order for this model. The serial# is XD60713444 and the Model ACQ6000ES0 Thanks!
Jane S July 26, 2016 for Model Number AEQ6000ES2 Frigidaire Dryer The E68 Error function keeps coming on and no buttons are stuck. I've read that it is either a faulty thermostat or the control board needs to be replaced. We're struggling right now, so to save money my husband could replace either one, but needs instructions as to how to access them. Then he will check continuity of thermostat and go from there. Please give me the procedure for accessing the thermostat and which one to check, and the control board, as well as the part numbers for both parts so after diagnosis the right one can be ordered. Thank you.
1 Answer Hello Jane. You will need to order 134557201NH for the part needed for the unit. Read More...
Harry July 20, 2015 for Model Number Frigidaire leq8000feo Dryer I am getting a e68. I can get the dryer working by pushing cancel sever times together with changing settings. Now it is staying on and the only way to stop the beeping is to leave the door open. I have checked and some say a stuck button. I have pushed the start and cancel button at the same time and nothing happens. Then they say the control board, but, there are so many I am not sure exactly which one fits this model. Is there any way to make sure it is the control board?