Mack July 20, 2023 for Model Number Frigidaire dryer hi i have a Frigidaire dryer i think i need a control board,,where is the model number located?? when i turn on dryer in 5 minutes it turn off with code 61...help...
1 Answer Hello Mack, you should be able to see the model/serial tag on the side of drum opening panel/frame once the door is opened, you can also try looking on the outer rear cabinet panel near the top. Read More...
Mark August 09, 2022 for Model Number DV48H7400EW/A2-0000 Could a possible bad control board cause the dryer to overheat ? I have replaced the element assy including the thermistor and thermometer and dryer stil overheats after 3-4 minutes. can a control board be cleaned? i cant think of anything elese causeing the overheating. Ducts are cleaared as well. I nneed to know before i PURCHASE A CONTROL BOARD
1 Answer Hello Mark,at this point likely the heater element relay on the control board is stuck closed, check this by just running a no heat cycle if the dryer is still heating, then the control board will need to be replaced,DC92-01626A. Read More...
Dominic November 28, 2021 for Model Number SC272ZP Thermador double oven keeps beeping. Cant reset it ?
1 Answer Dominic, Try to shut off the power to the oven for 5 minutes and then turn it back on. There may be a problem with the unit in which a control or touchpad may be the issue but normally will get an error code. Read More...
Gerri November 01, 2020 for Model Number GTDP490ED2WS The post for the control knob is broken. What is the replacement part for this?
Rich July 29, 2020 I ordered http://cdn.appliancepartspros.com/images/product/cache/wci-control-134557200nh-ap6890261_01_th.jpg I followed the instructions ,plugged it in and the circuit board blew up! It sounded like a gun shot went off. Smoke every ware, now what?
1 Answer The first thing I would do Rich is to verify that it was the correct part for my model. If is it correct then double-check the wiring was correct to the instructions. If that was all good I would start checking the wiring coming into the board looking for shorts or incorrect power being applied. If you write us back and provide a model number we may be able to provide more accurate and specific help. Read More...
Charles July 10, 2020 for Model Number FEFB9200ESO I need to remove the cover over the control panel. How do I do that without damaging it? It is plastic and I am concerned about applying too much pressure. I tried to find the cover on your web-site but can't find enough details to see how to remove it.
1 Answer Charles, To remove the front panel, you will need to first remove the main top of the unit. You will do this by pulling the unit out and there will be 2 or 3 screws on the back holding the maintop. Remove the screws and slide the maintop back and lift off. Once removed there will be screws on the backside and top of the control panel that you will remove to take the control panel loose. Read More...
Ken December 21, 2019 for Model Number Kenmore #1106600201 will your control part # ap6890261 fit kenmore model 1106600201
1 Answer Hello Ken, unfortunately the board in question is not compatible with the model number supplied. The correct control board for the model number supplied is part number WPW10317640. Thanks! Read More...
Roger December 02, 2019 for Model Number Aeq8000fso Dryer only runs on low heat. It gives no error code. Possible thermistor or control panel?
1 Answer Hello Joe,if the control panel temp selector is stuck on low heat setting then its the control panel/control board 134557200NH, if however, you can select high heat and the dryer does not seem to get hot enough, then start by checking the exhaust vent is not restricted. Next check if the dryer has the correct incoming voltage, use a multimeter and check for 240v at the rear terminals. If ok, you will need to check the heater element for any problems like a short or ground.It should ohm at about 12 ohms. Nec Read More...
George October 06, 2019 for Model Number AEQB7000EGO I have a AEQB7000EGO dryer that will not heat. Everything else works without a problem. I have taken apart and tested resistance on heating element, thermostat, thermal fuse and high limit thermostat and all came out good. I ran diagnostic and get e68 error. I tried some recommendations to check for stuck buttons on board but the heating element will still not turn on. What’s interesting is I have been dealing with heating element turning in and not turning on for months. Very random. Now will not turn on at all. Is recommendation a control board at this point?
1 Answer George,As far as the heater goes make sure the relay in the control marked RL2 is closed and you get a reading of 120 vac on both wires when the unit is running and trying to heat. Voltage in and not out then replace the main control. If all tests good then it would be an issue with the centrifugal switch in the motor and would need to be replaced. [motor] Follow the instructions on the tech sheet for the error code. Read More...
Barbara January 03, 2019 My clothes dryer quit in the middle of a load. A friend checked the power, and power source was working, but, nothing to the dryer. Bought a new circuit board. Power checks out good on meters, but, the dryer still won't start, not even light up.
1 Answer Barbara,We will need your model number to help you find the right parts for your unit. Please post another question with all your info included thank you. Read More...