Dan October 18, 2014 for Model Number KUCS03FTPA0 I am installing the redesigned switch however, the instructions do not tell me where the black wire should be inserted on the new switch and I did no see any markings on it either. Can you please let me know asap. Thanks Dan
1 Answer Dan, The tan wire will go on one side and the black would go to the other. Since it is only a 2 terminal switch then it will not matter which goes to which side. Read More...
Sue August 11, 2014 for Model Number Kenmore Elite - My trash compactor works, but only when I tape down the buttons. When I lift up on the lever it no longer initiates the compaction. Buy, I can tape the black button down (tricking the compactor to think that I have closed the door) and tape the white button down that initiates the compaction and the compactor will cycle. Is this the correct replacement part that I need to fix my trash compactor?
1 Answer Hello Sue. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Miriam July 01, 2014 for Model Number NA Hello I ordered and have correct replacement part W10342596 I found instructions online but no template: Do you have access to template please it was not included, Starting in the second quarter, compactors went to a new integrated switching redesign. The switch has changed from a normally open switch to a normally closed switch that is held open by a new actuator lever. Replacement parts for the old switch will sub to a kit that contains: a normally closed switch, an actuator assembly, toe guard, a template, two screws and an instruction sheet. Thank you
1 Answer Miriam, We do not have just the template for the kit. If your kit did not have the template then you would need to get another kit. Read More...
David May 05, 2014 for Model Number Kitchenaid compactor KUCS02FRPA1 The toe plate when pushed up activates the compactor. There is a metal switch that connects to the power switch when the door is closed. Where can I buy just the metal part without having to purchase a complete kit?
1 Answer Hello David, I'm sorry but this W10342596 is the only way I know of to get the part without buying a used part. Read More...
Jace January 30, 2014 My Whirlpool trash compactor is 18 years old. I need a off-on switch part #9871139 that I have not been able to find. Is there another off-on switch that would fit my compactor?
Jim November 22, 2013 for Model Number Whirlpool gold sound conditioned - 15" undercounter Our trash masher is 15 years old and still works fine except - I removed it to replace the flooring underneath it and when I put it back in the space the foot pedal that you push to get it open is very hard to push down, a lot harder than before it was removed. What might be the problem? Thanks Jim
1 Answer Jim, You will want to check to make sure that there is nothing caught under the foot pedal and check the linkage to make sure that the linkage is not bad. Also check to make sure that the unit is in square and leveled properly. Read More...
Alan September 28, 2013 for Model Number KUCS02FRPA1 Is JUST the metal actuator for the door switch available? The switch is O.K. The piece of metal that closes the switch when the door closes broke at the foot mounting.
1 Answer Alan, That's one of the reasons the actuator assembly was redesigned, and substituted to the Switch Actuator kit. Due to the changes, the parts are not interchangeable if memory serves well, But it's not that difficult to repair, and of course the kit comes with illustrated instructions and all the information needed. Read More...
Joe September 05, 2013 for Model Number kucso3ftpao Is the starter switch replacement kit a direct replacement, i.e. no drilling, cutting, etc. And will this break as fast as the one on our unit?
1 Answer Hello Joe. With it being a kit, it can require some modification to the unit. It should last longer than the original one for the unit. Read More...
Jerry May 25, 2013 for Model Number kucs03ftss0 I need to replace a metal plate that broke that makes contact to turn on and off the compactor. I understand that the part is now called an off - switch actuator. The old part number I think is 9871976. It does not look at all like the picture you show. Is this a replacement of a simple metal plate that looks like a door striker? I need help. I can not see paying this much money for a plate. I do not need a kit. I am not sure a kit will fit. It is help together by two screws. the size is 1/2" X 2". Thanks
1 Answer Jerry, The old part number 9871976 has been changed by the manufacturer to the kit part number W10342596 and will work for your unit. This was a manufacturers change and the metal piece cannot be gotten by itself. Read More...
Greg February 03, 2013 I have the new actuator assembly (w10242549) to replace the old w10155269 part, but am not sure how it fits. Any diagrams to help?
1 Answer Hello Greg, We do not have a diagram to show how actuator would be installed. The Actuator is held in by 2 screws and they both mount the same way. Read More...