Al August 21, 2016 for Model Number JES8850BAS The center of the left front (small/large) burner will not come on when I turn the control know to turn on only the small burner, but if I turn the control knob to the turn on the small burner with the outer burner ring, only the outer ring turns on. When I pulled the control panel off to check the control switch and connections, all appeared fine. After reassembly, the center burner still doesn't work and now the keypad to set the clock, oven, etc. doesn't work correctly. If I press either 2,3, or 4, the display shows "234" and if I press the "Enter" button, it sees it at pressing it twice.
1 Answer Al, This issue with the burner will be caused by a faulty burner element. For the issue with the control you will want to double check the ribbon connector at the control board. If the ribbon connector is seated properly and clean then the control panel would be the issue. Read More...
Harlan S. May 01, 2016 for Model Number JES8850BAS The touch pad does not work. Clock cannot be reset, all left hand options, options beneath the clock and right hand options also don't work. Cook top works perfectly. Suggestions. Thank you.
1 Answer Harlan, You're on target. The key pad circuits have started to degrade. Usually due to ammonia based household cleaners, but check the oven door at the top to make sure the door seals and there's no excess heat escaping from the top of the door onto the control panel. The part is in stock and available at this time. Thanks Read More...
Brian August 24, 2014 for Model Number JES8850BAS Is the control panel P/N AP4369444 an improved version of the old design if so what improvements were made? Thanks, Kell.
1 Answer Hello Brian! Yes, the control panel WPW10206079 is the manufactured replacement to the original panel used on model JES8850BAS. Unfortunately, we do not have the specs to verify the difference in the two panels or to verify the improvements made. Sorry about that! Read More...
Pierre May 05, 2014 for Model Number JES8850BCS Hi, The buttons on of my control panel do partially work. When I press the set up buttons, the option for the clock shows up, but when I push the arrow button, nothing happen. When I push the convect button, the words convect and bake show up, but nothing happen when I press the arrow for more options. The range surface elements do work properly, so are both timers, the warm surface and the warm drawer. The oven light doesn't work either. When I push the buttons back and enter at the same time, the door locked for cleaning and do unlocked when I push them again. The word continue shows up and when I push on that option, nothing happen. I would apreciate some advice regarding these matters ! Thank you Pierre
1 Answer Hello Pierre. Based on the information you provided, it sounds like the control panel WPW10206079 is bad and will need to be replaced on the unit. Read More...
Mike May 01, 2013 for Model Number JES8850BAS Hello. The buttons on the left side of my control panel, bake, convect, setup, options, etc, do not work. right side number functions and timer do. The clock displays. Do you believe that your part #AP4369444 will fix this, or is there other electronics behind this panel that need replacement as well. Thank you. Mike
1 Answer Hello Mike. Yes, you will need to order and replace the control panel WPW10206079 on the unit. Read More...
1 Answer Tony, It's not as hard as you'd think, here's the service maual information : " Control Panel 1. Remove power from unit. 2. Open oven door and remove screws securing control panel. 3. Remove screws located on the right and left sides of the control panel. 4. Grasp control panel on the far left and right sides and gently pull the control panel out and down. NOTE: Gently pull control panel out and down. 5. Remove infinite switch control knobs, infinite switches, indicator lights, rocker switches, and electronic control/clock (as necessary) and transfer to the new control panel." Just remember to label any wires you need to disconnect from the indicator lights or switches, and You'll do fine. Thanks and Good Luck 6. Reverse procedure to reinstall control panel. Read More...