Elise March 31, 2019 for Model Number ED5FHAXVB Ice bin will not release from door. I have removed all the ice...dispenser is working as ice was flowing fine. However, I cannot remove bin from door. I can't see what is keeping bin from releasing. Any suggestions?
1 Answer Elise, The WP2198573 Ice Bin is the least likely issue, the WPW10130497 Crusher Bin is more likely. It has a locking mechanism with a release button on the right side of the crusher bin " Hold the base of the storage bin with both hands and press the release button to lift the storage bin up and out." If you consistently use crushed ice, there is a possibility of ice forming between the door and the base of the ice bin, which can cause the latch assembly to "stick" and keep the bin from releasing from the door. Read More...
Greg January 09, 2018 The release button on the bottom of ice bin is broken and won't release to take out the ice bin. I need the part number, please.
1 Answer Hello Greg, I'm sorry but we will need to ask you to post a new question including the model number from your units' I.D. tag so we can recommend parts that can be guaranteed to work properly on your unit. Thank you for your patience and understanding in this matter. Read More...
Charlotte B June 14, 2016 for Model Number ED5JHAXTQ01 My ice is freezing at the bottom of the bin in the inside of the freezer door. I have replaced the kit on the outside of the freezer door where it dispensing the ice with the updated insulation, heater, and closing mechanism but that did no correct the problem. Now I want to replace the ice bin. I know I broke the button release catch one of the first time it froze up when trying to get it off and melted some of the plastic when I was defrosting the ice. Hoping this will solve the problem. If not I don't think I want to go into the freezer door itself. So I will just have to insulate the air from the dispensing chute with something and have an ice bucket instead of ice dispensed through the door. Please give me the correct part number for the ice bin in the door for my model number. Thank you.
1 Answer Charlotte, The part number for the complete ice bin for your unit will be WP2317251. Read More...
Noe G. June 11, 2016 for Model Number ES5LHAXSA01 Ordered # FG0302409 and received ice bucket W10204465A that did not fit refrigerator Model ES5LHAXSA01 .Amazon approved return of item however I do need complete & correct ice bin, can you help ?
1 Answer Hello Noe, I'm sorry but the replacement complete ice container 2320332 for the model number provided has been discontinued by the manufacturer and no satisfactory substitutions have been provided. Read More...
Karen September 12, 2014 for Model Number 10658976702 I took my ice bin caddy out to dump ice in a bucket and now I cannot get it back in. I have tried and tried but it is not fitting back in.
1 Answer Karen, If the ice bin was difficult getting out it by be an issue of the shaft sliding up. Using the blunt end of a screwdriver or a hammer, tap down on the shaft. Just go a little time and try to put the bin on until it sits flush on the door. Read More...
Joe Mccloskey November 09, 2013 for Model Number 106.55523400 My ice freezes up in the bottom of my ice bin. I want to replace the whole unit that lifts out to dump ice.
1 Answer Joe, The ice bin part number for your unit would be WP2258236. With ice freezing you will want to check the dispenser door for an air leak. Read More...
Kathy H. June 29, 2011 for Model Number 10657026601 I need the base to my ice bin, the pegs are round and one is broken. The ice will not dispense. Also, I did not know that the ice container came in two separte parts, when I take it out the whole thing removes by pushing an oblong button on the base. I do hope you can help me. Thanks!
1 Answer Hello Kathy. For the base of the ice bin, you will need to order WP2212372. Hope this helps. Read More...
Cinda C. March 08, 2011 The pegs on the bottom of the ice bin, are they round or oblong, I need the oblong for my KitchenAid Model# KSRL25FTST00. Thanks Cinda
1 Answer Cinda, the pegs on WP2198573 seem to be oblong. This ice bin matches your Kitchenaid model KSRL25FTST00. Thanks! Read More...