Charles February 24, 2018 for Model Number gi5svaxvl01 I first noticed the control panel display blank. Interior lights are working but I haven't heard the compressor kick on, even after unplugging.
1 Answer Charles, This issue sounds like it would be a control board that is faulty and would be part number WPW10310240. Read More...
Mark K December 13, 2017 for Model Number GI5FVAXVB02 What are the instructions to reset or program this model after replacing the control panel. Getting PE0000 on display and can't get it reset.
1 Answer Mark, Here are the instructions for the refrigerator programming. Programming Mode:NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.1. Press and hold the Door Alarm Keypad.2. Press and hold Freezer Temperature DOWN /- Keypad within 3 seconds.3. Release the Door Alarm Keypad and wait 3 seconds.4. The control will display PE to indicate the programming mode.5. Entry is confirmed by pressing the Freezer Temperature DOWN /- Keypad once more.6. The control will display the current Program CODE. This value should be validated with theProgram CODE printed on the unit serial plate.NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door Alarm Keypad for 3 seconds.7. Press the Refrigerator Temperature UP /+ Keypad or Refrigerator Temperature DOWN /- Keypad to change the digit value with each key press.8. The decimal point indicates the selected digit. Press the Freezer Temperature UP /+ Keypad to select the next digit.9. Once the desired Program CODE is entered, press and hold the Freezer Temperature DOWN /- Keypad until the Program CODE begins flashingindicating it has been saved.NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a ProgramCODE of 0000).Once the Program CODE has been saved the Programming Mode is exited by pressing any key. If the new code is incorrect thisprocess should be repeated.The Programming mode can be exited at any time by pressing Door Alarm key for 3 seconds or will exit if unattended for four minutes. Read More...
Rita September 15, 2017 We replaced the control board (WPW10310240) on our Whirlpool refrigerator. When we plugged it back in we got PE0000. We followed all the instructions to program it but nothing is working. Can you please help? Rita
1 Answer Hello Rita. You will need to follow the program steps step by step and in a timely manner. If you pause, you have to start over again. Read More...
Gary September 12, 2017 for Model Number KitchenAid #KFIS20XVMS00 Water and Ice Despenser does not work. Display seems to be working fine. If I turn push the cooling off switch until the cooling off light comes on and then turn the cooling back on the ice and water works for a short period of time and then quits again. I removed and unplugged the front display and reinstalled but no changed. I also noticed that it seems to work when the compressor is not running? Do you think the main board is bad?
1 Answer Gary, With this issue it does sound like the issue will be a faulty main control board that would cause the ice and water to stop working. Read More...
Jon May 25, 2017 for Model Number MFI2266AEQ10 I replaced my HV board due to flashing panel and ice door opening and closing constantly. I also reprogrammed in the code off the panel and programming mode but still have no ice or water being dispensed.
1 Answer Jon, With the dispenser still not dispensing ice or water this would most likely be a issue with the dispenser control board. Read More...
Sivakumar April 27, 2017 for Model Number 59678533801 I have Kenmore refrigerator 59678533801 and having problem that display on front panel blank but while pressing any button or dispenser flap all button indicators are on. I tried to removed the power plug and back on I heard same sound in the back side of the front panel and the ice flap open and closed. then the sound off. Can you help me how to fix this problem.
1 Answer Sivakumar, The most likely cause for this issue will be a faulty main control board which is part number WPW10310240. Read More...
Corey April 06, 2017 for Model Number AFI2538AES I lost the control board programming code. The sticker with it on it was taken off. Can some one help?
1 Answer Hello Corey, You can try code 1141. If that doesn't work correctly you can try 0302. Read More...
Jim H March 29, 2017 for Model Number JFI2589AEP2 My Jenn Air refrigerator stopped running. The control panel would not work. I tried to replace the control panel but it did the same thing...nothing. I sent that part back and ordered the main control board. I replaced that. A fan kicks on but now the control panel display is blank. It lights up behind the screen but none of the buttons work. The wiring at the top of the door appears to be ok. Is it possible that the control panel is bad as well?
1 Answer Hello Jim. Yes, based on the information you provided it sounds like that panel is bad also. Read More...
Juan March 25, 2017 for Model Number MFI2269VEM3 I have to replace the control board - part number W10310240A and all the control boards I find in the market don't have the letter "A" at the end of the part number, i.e. part numbers in the market are W10310240. Will those boards work exactly the same as the one ended in "A"?
1 Answer Juan, We are not showing the part having an A at the end of it and you will want to get part number WPW10310240. Read More...
Gary March 08, 2017 for Model Number GI5FSAXVY02 After replacing the main board (WPW10310240) on my Whirlpool Refrigerator/Freezer, I plugged it back in and PE0000 came up flashing on the display panel. Is this normal after replacing the M B?
1 Answer Hello Gary. Yes, the unit will need to be programmed. Here are the instructions. Programming Mode:NOTE: The Program Code is located on the Serial Plate on this unit after the word Code.1. Press and hold the Door Alarm Keypad.2. Press and hold Freezer Temperature DOWN /- Keypad within 3 seconds.3. Release the Door Alarm Keypad and wait 3 seconds.4. The control will display PE to indicate the programming mode.5. Entry is confirmed by pressing the Freezer Temperature DOWN /- Keypad once more.6. The control will display the current Program CODE. This value should be validated with theProgram CODE printed on the unit serial plate.NOTE: If the Program CODE is correct, the Programming Mode is exited by pressing Door Alarm Keypad for 3 seconds.7. Press the Refrigerator Temperature UP /+ Keypad or Refrigerator Temperature DOWN /- Keypad to change the digit value with each key press.8. The decimal point indicates the selected digit. Press the Freezer Temperature UP /+ Keypad to select the next digit.9. Once the desired Program CODE is entered, press and hold the Freezer Temperature DOWN /- Keypad until the Program CODE begins flashingindicating it has been saved.NOTE: If you attempt to enter an invalid Program CODE the control will not save the new code, but will beep. (The unit will NOT run with a ProgramCODE of 0000).Once the Program CODE has been saved the Programming Mode is exited by pressing any key. If the new code is incorrect thisprocess should be repeated.The Programming mode can be exited at any time by pressing Door Alarm key for 3 seconds or will exit if unattended for four minutes Read More...