Marj April 17, 2019 for Model Number LSN 2000JQ1 The top front of washer has sprung up and won't stay down. Is there a clip or push pin that goes in the front?
1 Answer Marj, there should be a 5/16 screw that holds all 4 corners of the top down to the bottom cabinet. You would need to remove cabinet from off of the base to get to the screw hole,, it feeds in through the inside to hold the top down. Read More...
Linda March 08, 2018 for Model Number ATW4475VQ0 How do we get the cabinet back on the washer..we had to replace the water lines and cant remember how it goes back on
1 Answer Hello Linda. There is a good video on the water valve page showing how to reinstall the cabinet. Here is a link for you. Thank you. http://www.appliancepartspros.com/whirlpool-valve-vac-break-wpw10144820-ap6015761.html Read More...
James March 13, 2014 for Model Number NTW4500VQ1 How do you put the back panel back on? I don't remember how to put the clamps on.
1 Answer Hello James, When you put the cabinet on you have to hook the front bottom edge under the bas of the unit. Then when it is set onto the unit, line the back up with the cabinet and the clips hook into the slots in the main back. They will then pop into position with a small amount of downward force. If you look at the parts illustration, you will get an idea of the direction they are inserted. Please note that the illustration does not show the back end making the 90° upward bend where the clips go into the main back slots. It does illustrate the hooked end toward you as it should be for proper assembly. Read More...
Annette M. April 29, 2012 for Model Number 11092582210 How to take clip off the top off a washer machine?
1 Answer Hello Annette. Here is a link to a video of how to remove the clip WP62780. http://www.youtube.com/watch?v=OlAFQnkapLM Read More...
Tami November 21, 2011 for Model Number wtw5200vq2 My top isn't connected to my cabinet anywhere. How can I fix it?
1 Answer Hello Tami. You will need to order 4 screws WP3390631 to secure the top to the cabinet. Then you will need to remove the cabinet from the washer. Disconnect the power to the unit. Remove the two screws in the back corners of the control panel securing the control panel. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. You can now access and install the screws. Hope this helps. Read More...
Bill November 14, 2011 for Model Number 110.22712100 All the clips and screws that hold the top to the cabinet were missing on a washer I just bought. What all do I need, and what will it cost.
1 Answer Hello Bill. You will need to order 2 clips WP62780 and 4 screws WP3390631 for the top. Hope this helps. Read More...
Kelly November 09, 2011 for Model Number roper_ras7133kq1 washer How do I remove the front of the washer?
1 Answer Hello Kelly. Disconnect the power to the unit. Remove the two screws in the back corners of the control panel securing the control panel. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips WP62780 securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. You can now access and replace the part you are needing to. Reinstall in reverse order. Hope this helps. Read More...
1 Answer Hello Steve. Disconnect the power to the unit. Remove the two screws in the back corners of the control panel securing the control panel. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. You can now access and replace the lid switch 3949247V. Reinstall in reverse order. Hope this helps. Read More...
1 Answer Hello Joey. Disconnect the power to the unit. Remove the two screws in the front corners of the control panel securing the control panel. Pull the control panel forward and flip it backwards. Next unplug the lid switch and remove the two brass colored clips securing the cabinet to the back wall using a flat blade screwdriver to pry them out. Pull on the front of the cabinet and slide the cabinet off the frame of the washer. Reinstall in reverse order. Hope this helps. Read More...
Carolyn September 10, 2011 for Model Number Admiral Washer ATW4475XQ0 The washer fills with water but when you close the lid and pull the cycle control knob out it does not start washing. What is wrong
1 Answer Carolyn, You may have a loose gray wire or bad circuit in the lid switch WP8318084. Does the washer spin and drain ? if it does, then we're looking at a timer problem, most likely. Good Luck and Thanks Read More...