Mike November 09, 2015 for Model Number MEW6627BAB Our Maytag oven MEW6627BAB when last used made a crackling/sizzling sound was heard from the control panel followed by smoke. Power was disconnected. I took apart the control panel and did not notice anything until I removed the front clock/control board. The back of the circuit board showed evidence of some charring and possible solder melting on the back side bottom corner of the board. When powered back up the clock works but none of the oven functions work when selected (no elements heat up, convection fan does not activate, only the cooling fan for the control panel turns on when broil is selected - this is all true for both upper and lower oven). I assume that I am correct in that I need a new oven control board. However, should I be concerned that something else failed/faulted causing the control board to short? Any way to test for this?
1 Answer Hello Mike. Just make sure the wiring harness is good on the unit. If so, then you should just need to replace the control board. Read More...
Tracy September 12, 2015 for Model Number JGS9900BDS We keep getting error message EE-214 and M-214. We replaced the igniter. Do we need another part now?
1 Answer Hello Tracy. Based on the errors, it sounds like the control board WP8507P236-60 is bad and will need to be replaced on the unit. Read More...
Marva April 28, 2015 for Model Number MEW6630BAW My oven has gone crazy - it is indicating F2 can you say what fault that represents?
1 Answer Hello Marva. The F2 error code on this model of range indicates that the electronic oven control board detected an over temperature condition in the oven. If the oven actually overheated, then you could have a welded contact on the electronic oven control board. If the oven did not overheat, then you could have a bad oven temp probe or a wiring issue. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Rick December 22, 2014 for Model Number MEW6630BAB We used the oven's self cleaning feature. Now the fan will not go off.
1 Answer Hello Rick. Test the thermostats in the top and see if the one for the fan is not opening back up. If not, replace it. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Michael October 12, 2014 for Model Number GBD307PDS09 A few years ago I had to replace both components, the control pad and panel. Recently, I started getting strange behavior from the unit. Autoclean would ask if I wanted it started. I took it apart and the ribbon cable lock arm was broken. Now I am trying to locate that one part only. Anyone have any idea where I can get this one small part?
1 Answer Hello Michael, The only way you will get this by itself is from a used unit. The only other way to get it is with the control board WPW10438751. Read More...
Sammy October 21, 2013 for Model Number part no 71001872 clock Is there a trick to remove the ribbon connector from the existing unit?
1 Answer Hello Sammy. Squeeze the tabs on the side of the connector and lift upward to unlock the ribbon cable and remove it from the control board on the unit. Read More...
Daniel August 26, 2013 for Model Number JES9800AAB (Jenn Air downdraft stove with conv. oven) Jenn Air downdraft stove---nothing will activate and have a beeping--error F1-7----turned off power as suggested, even leaving the power off overnight, in the manual to troubleshoot problem---did that 3 times and stove came to life again--but was short lived--now back to error F1-7 and beeping. What has failed?
1 Answer Hello Daniel. Membrane disconnected. Ensure ribbon cable is securely connected, inspect ribbon cable and connector (shorts, breakage, corrosion, etc.). If OK, replace control. Read More...
Robert May 21, 2013 The plastic casing holding the control panel snapped off. The control panel works fine, but there is no way to keep it secure. Is it possible to purchase the casing part without having to buy an new control panel? Thanks
Steven March 31, 2013 for Model Number WW30430W I purchased the 71001782 to replace the clock/control board for the WW30430W, the original board has a ribbon type connector and the replacement has a wire/pin type connector. Is there an adaptor or have I purchased the wrong part?
1 Answer Hello Steven. WP71001872 does have a ribbon connector on it. It is the lage black connector and must be pulled up to unlock and install the ribbon cable. Read More...
Steven March 29, 2013 for Model Number jenn air expressions double wall oven I purchased the 71001782 to replace the clock/control board, the original board has a ribbon type connector and the replacement has a wire/pin type connector. Is there an adaptor or have I purchased the wrong part?
1 Answer Steven, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...