Gaines April 06, 2024 for Model Number WSF26C2EXY02 The ice maker stopped making ice. Using the refrigerator diagnostics, I verified the ice container was working correctly. In looking at the ice maker, it wasn't initiating a harvest. I replaced the ice maker (AP6017832), but it still isn't filling or harvesting. Is it possible the control board is at fault? How do I check that the ice maker is getting voltage from the control board?
1 Answer Gaines, it would be recommended that the freezer temperature be verified as reaching 0°F with a thermometer. If it does not reach proper temperature, the ice maker will not harvest. To test the voltage to the ice maker, the black wire with white stripe at connection P3 pin 3 of the control can be tested for 120VAC. If voltage is present, the main control is good and the voltage directly at the ice maker would need to be tested with the door switch taped shut, and the ice bin sensors having clear line of sight to each other. Read More...
George December 16, 2023 for Model Number GSS26C4XXF03 Hi, Whirlpool GSS26C4XXF03 (Gold Series Side by Side with IceMaker. Both compressor and condenser fan will only run for a few seconds if one taps on the main control board in the area of the relay and capacitor - on occasion, both will run for hours, but then recycle and not run. When powered up initially, the relays can be heard clicking (not the over voltage on the compressor) until the relay for the fan and compressor click, then the fan spins once or twice and then stops. Tried re-soldering those capacitor pins, but will still only power momentarily when tapping hard on the relay. Thoughts?
1 Answer George, based on the information provided, the main control W11088499 has failed and would need to be replaced. Read More...
Don May 09, 2023 for Model Number 106.51134210 I have replaced the interface board (located on the freezer door front panel) and all water supply pumps on the refrigerator and still no water or ice flow. Could the refrigerator control board be the item that causes no water or ice flow?
1 Answer Don, if the water filter 9081 has been verified as being good, the wires at the door hinge would need to be inspected for any broken wires. If there is not a broken wire, the most likely cause of failure would be the main control W11088499. Read More...
Jorge April 23, 2023 for Model Number 10651139210 Why my ice maker keep overflowing? I have replace the filter and replaced both water solenoids as well. What device stops the water filling for the ice maker?
1 Answer Jorge, The water valve is what supplies the water but with the valve having been discontinued then this would likely be an icemaker issue. Read More...
George October 12, 2022 for Model Number GSF26C4EXT02 Water Filter is leaking inside refrigerator. No water to water dispenser or ice maker. Replaced inlet valve WPW10238100. Having same problem.
1 Answer George, this would be caused by a filter not seating properly, a broken filter EDR1RXD1, or a cracked filter housing WPW10238123. Inspecting the filter for any cracks or improper seating can help identify the specific failure. Read More...
Christopher Zink September 23, 2020 for Model Number WSF26C3EXF01 My fridge has stopped cooling on both sides. Lights work but The fans and the condenser do not come on.
1 Answer Christopher Z, Based on the information provided Check for power to the condensor fan and compressor on the red and white wires. Check for the power out of the board at P1-4 and P1-2 if none check the thermistors if bad they would need to be changed, if good it would be the board. Read More...
Donald December 30, 2019 for Model Number GSF26C4EXT02 Hi, ice dispenser through the freezer door stopped working. I changed out the auger motor and it worked for 6 months then stopped working again, and I bought another one and installed it. That one did not work at all. The door shut is working fine. I swapped the water dispenser pad with the ice dispenser pad and still no ice dispensing. The water dispenses fine and the ice is being made fine--just no dispense through the door... Help! Thanks, don
1 Answer Donald, You will want to test to see if there is power getting to the auger motor. If there is not then check for a wiring issue at the door hinge. Also, check for power from the control board to the auger motor. This will likely be a control issue if there is no power to the auger motor. Read More...
Pg October 12, 2019 for Model Number GSC25C5EYY00 All the led lights in both the refrigerator and freezer side suddenly went out. Everything else works. Tried power cycling the refrigerator but no luck. What would be the cause?
1 Answer PG, This unit has an LED driver board that would need to be checked. There is only one connection and you will need to test the pins for voltage in and out. Any readings other than those listed and this control would need to be replaced. W11038857 Read More...
Linda June 19, 2019 for Model Number WSF26C3EXF01 Ice will not dispense. Installed new auger motor and ice dispenser pad. Now what?
1 Answer Linda, you will want to check to see if the door chute motor will open up when the dispenser paddle is engaged. If the door chute does not open up, then the issue would be with the display assembly WPW10372206. If the door chute does open up, then you will want to check the main control at connection P13. At connection P13 you will want to test the blue wire (with the red probe of a meter) and the gray wire (with the black probe of a meter) together for 140VDC when the dispenser switch is engaged. If there is not 140VDC, then the main control W11088499 has failed. If there is 140VDC, then you will want to inspect the wiring harness and connectors going from the control to the door for any signs of a break or corrosion. Read More...
Guillermo March 27, 2018 for Model Number GSF26C4EXY02 My refrigerator stops working every morning. The freezer and refrigerator sides are both warm. I have to disconnect the power to start the unit cooling again, but every day this happens again.