Jim March 31, 2014 for Model Number GBD307PDS09 When the oven is turned on for preheat after 3-4 minutes the display goes blank and the oven shuts off- Then after about 30 minutes the display will come back on and the oven holds temp. Is this an issue with the board or transformer.
1 Answer Hello Jim. It sounds like the electronic control board WPW10438751 is bad on the unit. Make sure there is no wiring issue with the unit. If not, then you will need to replace the board on the unit. Read More...
Phil V. March 13, 2014 for Model Number RBD275PDS15 My display went dark but some keypad buttons still beeped. I got the control board from you today and now display works. I get F5 E1 message, followed by E1 F5. Then after a while only F5 stays on the display. I can set the clock but when I hit start it goes back to the F5 display. I'm guessing now you will say I need the keypad. That is a crappy connector for the ribbon connector by the way - I have played with it but no improvement.
1 Answer Hello Phil, The F5 E1 fault code is the code indicating the Self-clean latch will not lock/unlock. The tech sheet states the following on this issue: 1. Check the latch assembly: latch arm pivot joint, arm/motor connection, plunger and hook springs. 2. Check the Latch Motor: - Check for firm electrical connections. - Disconnect the two wires from the motor and measure the resistance of the motor. The resistance should be approx. 2450O. If the motor is open (8O) or shorted (0O), it should be replaced. 3. Check the Latch Switch. Disconnect it and use a continuity tester: - Door latched = switch closed, continuity should read 0O. - Door unlatched = switch open, continuity should read 8O. 4. Check Door Open/Closed Switch. Disconnect it and use a continuity tester: - Door open = switch open, continuity should read 8O. - Door closed = switch closed, continuity should read 0O. 5. Check Sister Board. - Check connections, latch motor – sister board. - Replace sister board. 6. Check power and element connections. 7. Replace control. Read More...
Craig February 17, 2014 for Model Number RBD245-PDT14 Whirpool electric oven Display is off. Oven beeps 5-6 times every few minutes. Reset breaker, can hear the start-up. Oven lights come on. Don't want to replace the control board unless I know this will fix problem. Beeping and no display is trying to tell me something but I don't know what. Thanks for any troubleshooting help.
1 Answer Hello Craig. The problem that you are describing is a control board failure. Part# WPW10438751 should fix the problem. Read More...
Jim January 28, 2014 for Model Number Rbd306pdbb The code came up F2-E6. I changed the torch pad and having the same problem.
1 Answer Hello Jim, Since this is not a valid code on the tech sheet for the appliance, the issue is going to be the control board 4452242. Since the board is no longer available, you will need to contact corecentricsolutions.com and make sure they support this board. If they do, you will have to send it to them for repair. You should take several pictures of the wiring to the board from different angles/directions so you will not have issues re-connecting it when it is returned to you. Read More...
Johnindallas December 18, 2013 for Model Number GBD307PDB09 Have a E0 F2 error code, oven cycles through when repowered, starts to heat then faults out, I can get oven to continue to heat by hitting upper oven button then waiting til " start?" Appears then hitting start, runs for 1-2 minutes faults out. Can't adjust temp above 350 on touch pad. Tried isolating power, checked connections. Control board or touch panel?
1 Answer Johnindallas, The F2 EO error code represents a key that has been held down too long or a key is shorted. Check the keypad connector for firm connections. Press cancel. If error code returns after 60 seconds then replace the keypad. If not then replace the control board. Read More...
Taya December 08, 2013 for Model Number gbd307pdb09 Oven screen is blank but when you open doors the light comes on. When you push the buttons they beep but nothing happens except you can turn the light on and off. When you push the start button you get two beeps followed by three beeps.
1 Answer Hello Taya. Check the control fuse and see if it is bad. If not, you will need to replace the electric control on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Chad November 20, 2013 for Model Number RBD305PDS15 We have a Whirlpool oven model RBD305PDS15. The oven has shown a PF message on the display for the past few weeks which we could reset and the oven work. Now there is no display and it only beeps when you press the keypad. I've checked only and it seems that I need an oven control board. I've seen several different parts numbers and don't know know which one to order. I've seen 8302319, W10406070, and W10438751. Which one should I be looking for? Thanks.
1 Answer Chad, Before ordering the control board you will want to check the transformer first. On the control board you will want to check the P16 connector from pin 5 to7 for 120 vac going into the transformer WP9760587. If there is 120 vac then check same connector pin 2 to 3 to see if there is 12 vdc coming out. If not then the transformer is bad and would need to be replaced. If there is then the control board WPW10438751 is faulty. If there is not 120 vac going to the transformer then the control board is faulty. Read More...
Jonathan November 07, 2013 for Model Number RBD245PDS14 I have a whirlpool double oven and the control panel does not light up and I get beeps when a button is pressed. I checked the transformer. I took 1 wire off and checked the continuity and it read 0. I bought a new control panel and still nothing. What is my next step control board maybe. Before I change out the control board is it anything else I can check.
1 Answer Hello Jonathan. You will need to order and replace the thermal fuse WP4451042 in the unit. It sounds like it is bad. Read More...
Tom October 22, 2013 for Model Number Whirlpool Oven RBD306PDB14 I have a Whirlpool Wall Double Oven RBD306PDB14. The display of my oven stopped working (blank) few days ago, but the oven lights come on and some of the control buttons make beeps when pushed such as the Bake, Hr, Min, Temp ... buttons. The Start button does not beep when it is pressed. How do I know if I need to have the Control board replaced or some thing else? I also checked the thermal fuse (part # 4456654) and it has continuity. Is there any thing else that I should check? If I need the Control Board for this oven, what would be the correct part number for it? Thanks
1 Answer Hello Tom. You will need to order and replace the control panel WP8300437 on the unit. Read More...
Patrick October 08, 2013 for Model Number Whirlpool RBD275PDB14 I need to replace the Oven Control board (w10406070) and can't see an obvious way to get the front panel off (control panel assembly) in order to get access to it. I've removed 4 scress below the panel, but they seem to only hold a metal tab/flange in place. Thanks, Pat
1 Answer Hello Patrick. Remove the side trim pieces and then remove the 2 screws on the bottom corners of the control panel. Lift it upward and off of the unit to remove it. Read More...