Sonja C November 18, 2016 for Model Number JDB8910AWW I have model JDB8910AWW purchased/installed in 2002. SN27625772AL. It fills and runs and then at about 65-66 minutes stopped...I could hear clicking like it was trying to start to either empty or continue to next phase but did not continue. I did trouble shooting and tried all cycle buttons and I have all lights and cycle times glowing for every cycle and each cycle starts...Is this a module replacement or a latch replacement. There is slight flickering of lights when the cycle button is changed to another one. If a module would it fit with the current white top cover. This dishwasher still performs nicely but is 14 years old.
1 Answer Sonja, You will want to check to see if the drain pump is getting power to it as this would be about the time in the cycle in which the unit would need to drain. If the drain pump is not getting power then the control board of the unit would be the issue. Read More...
Allie April 21, 2016 for Model Number JDB8910AWB My serial number is 27290970AC. My dishwasher panel only has 12 buttons. The control panel picture above listed for this dishwasher shows 13 buttons. What would the correct part number be for my dishwasher. Thanks!
1 Answer Hello Allie. You will need to order WP99002827 and the extra button will not be used on the unit. Read More...
Dave November 11, 2015 for Model Number jdb8910aws I need a control panel for my dishwasher what is the part number? Thanks
1 Answer Hello Dave. The control panel 6-915584 has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Phil August 09, 2014 for Model Number JDB8910AWQ The dish washer fills with water and runs. When it gets down to 50 minutes it sticks there. If I push the drain button it just clicks in the control panel. So is my control panel bad?
1 Answer Hello Phil. You need to check the drain pump on the unit. Check and see if there is power coming to it and it does not run. If so, you will need to replace the pump on the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Brian S April 19, 2014 for Model Number JDB8910AWS Serial number starts with 27. I have had to replace the control panel before for a different reason. Today it started making buzzing sounds then i smelled the "burning components" smell. Upon visual inspection of the board there were no burn marks but some discoloration around a few of the components. I think the board is fried or is soon to be. Is the PS2100158 the correct part for my appliance and version? Thanks a ton!
Jeremy March 20, 2014 for Model Number JDB8910 I have a Jenn-Air diswasher bought in 1999 with a bad control board, it smells like burned and has black coming our around one of the relays. Think around $499 was paid new, the board was replaced once years back so my question is do I replace the board again for $180 or buy new? Is it worth putting almost $200 into a unit that's 15 years old? It's still a beautiful looking and operating unit, really still looks like new. I hate the idea of paying $500 for a new unit but what are the odds the pump or some other component will go bad in another year or two? Part I need is below: Control Assembly (le Part Number: AP4113561 MFG Part Number: 99002827 Made by: Whirlpool
1 Answer Hello Jeremy. It does sound like the board needs to be replaced. As for the valve we have no way of telling you if it is worth the repair. Sorry. Read More...
Jo Ann October 22, 2013 for Model Number JDB8910AWB I have power to the control board, timer starts, the macine fills after a minute is shuts down and begins to flash, everything stops is it the control board?
1 Answer Hello Jo Ann. Make sure the door lock assembly is good. If so, you will need to order and replace the control board on the unit. Read More...
Diane July 24, 2013 for Model Number Quiet series 2 jennair dishwasher My lock button is on. I cannot get the machine to start on any cycle.
1 Answer Hello Diane. Try holding the button for 3 seconds to clear the lock light. If it does not clear, you will need to replace the control panel on the unit. Read More...
Kyle February 16, 2013 for Model Number jenn-air dishwasher model# jdb8910awb ser #27192424aa Need new control board but not sure which one? Please advise. Thanks, Kyle
1 Answer Kyle, the replacement control assembly listed for your model/serial is part number WP99002827. Thanks! Read More...
David P. July 08, 2012 for Model Number JDB8910AWB We have the Jenn-air quiet series dish washer Model #jdb8910awb, serial #27616409cl. Which control assembly do I order as there are several different ones listed.
1 Answer David, according to your model/serial number the replacement control assembly needed is part number WP99002827. Thanks! Read More...