Charles K September 23, 2011 for Model Number mah6500awq I Disconnected the motor and checked oms on black and white terminals on the motor reading was 0 do you think the motor is OK? Thanks, CK
1 Answer Hello Charles. To test the motor WP22003856, you will check across blue and black, white and red, and orange and yellow. Each one should read between 2 to 3 ohms. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Charles K September 22, 2011 for Model Number mah6500awq Not getting power to motor. All wires seem to be ok,no spin. Washer fills,pumps ok. Thanks! CK
1 Answer Hi Charles. It does make sence that you already verified power to the board but not out to the motor. Did you use the tech. sheet and try to use the diagnostic mode to verify if anything else is an issue? The control board is part # WP22004257. Thank you. Read More...
Charles K September 21, 2011 for Model Number mah6500awq What do I hook it too? Don't see how it fastened to any thing. Is there a diagram or anything? Thanks again for your help, you help to make my day! CK
1 Answer Hello Charles. It just lays inside the dispenser to where you can reach it if you need to unlock the machine. Just push it to the left side inside the dispenser, and that way it does not get in the way of things. We don't have a diagram to send to you. Hope this helps. Read More...
Charles K September 21, 2011 for Model Number mah6500awq Thanks so much! another question. On the Lock assembly there is a little tail. Where does the loose end go? CK
1 Answer Hello Charles. The tail on the lock assembly WP22003593, goes over to the dispenser to unlock the door if needed. Hope this helps. Read More...
Charles K September 21, 2011 for Model Number mah6500awq Got the part works great thanks! Now more problems, motor won't start or spin. The first code I had was LR. Help. Thanks CK
1 Answer Hello Charles. Based on the code you provided, you will need to test and see if there is power coming to the motor and look for loose connection inside the machine and broke wires. If all is good, and there is power coming to the motor, you will need to replace the motor WP22003856. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Charles K. September 17, 2011 for Model Number mah6500awq Can't close door manually and won't lock as you recommend a latch assembly but would this problem also effect the spin operation? Thanks ck
1 Answer Hi Charle's. Yes, the door latch for saftey purposes will not allow the machine to reach high speed spin. Part # WP22003593. Once the door is latched ,the spin enable switch will lastly be engaged and door locked light will be shown. Thank you. Read More...
Charles K. September 16, 2011 for Model Number mah6500awq With door is closed I hear a click led comes on but latch doesn't lock. Help _
1 Answer Hello Charles. Test and see if there is power coming to the door latch. If so, and the door does not lock, you will need to replace the door latch WP22003593. Hope this helps. Read More...
Klapp September 13, 2011 for Model Number mod# mah6500awq ser# 20784739at The door fails to lock. The washer will not pump water. The error code I see is LR & FL. The washer will not lock and it failed to pump all the water out. The washer will not do anything now.
1 Answer Klapp, The codes first "LR" ( locked rotor) indicates the motor does not run or the control board is not seeing the motor run. The "FL" (failed lock) indicates the door lock switch circuit is not being seen by the control board. You should try opening the control panel console(three screws across the back of the console top, and push backwards on the console and pull the top of the console towards the front of the washer to"roll" th console and access the Wiring diagram and tech data sheet and conduct the diagnostic codes and the board output tests according to the sheet. We'll have a better idea of the issues, once you do. Thanks and Good Luck Read More...