Steve A. January 19, 2013 for Model Number MF 12569 VEM2 I broke the lid peg on the left support of the deli drawer on this refrigerator. Can you give me the correct part # for the left side? Thanks, Steve
Kaida January 16, 2013 for Model Number Whirlpool GI6SDRXXQ00 RE: GI6SDRXXQ00 Whirlpool. Let me try this again.... I broke the small plastic peg on the right endcap for the deli drawer (...this seems to be a design flaw since it is so flimsy). My husband has tried to repair it twice with superglue, but it wont hold. Need to replace this part. Can you tell me the part number I should order? Is it AP4455176?
1 Answer Kaida, the right end cap W10874836 is the correct replacement and will fit your model GI6SDRXXQ00. Thanks! Read More...
Kaida January 16, 2013 for Model Number Whirlpool refrigerator GI6SDRXXQ00 right support for deli drawer I broke the small plastic peg on the right endcap for the deli drawer (...this seems to be a design flaw since it is so flimsy). My husband has tried to repair it twice with superglue, but it wont hold. Need to replace this part. Can you help me locate the part I need? Thank you. Kaida
Carole January 14, 2013 for Model Number MFI2569VEM Facing the frig, the left rail for the deli drawer came off. Any idea how to get it back on?
1 Answer Hello Carole, If this is the metal rail that goes to the bottom drawer there are 2 screws that hold the rail in place. You would need to put screws in. Read More...
Paul S December 14, 2012 for Model Number MFI2569VEB3 When installing the left drawer end cap,part # 12656106, when is the lid put onto the endcap?
1 Answer Hello Paul. Once both endcaps are installed into the unit, you can p[lace the lid into the endcaps. You will need to flex it slightly to insert the pegs into the holes. Be careful not to break it. Read More...
Ana December 12, 2012 for Model Number mfi2569veq The right side of the wide n fresh deli drawer has a broken tab. This is where the drawer attached with the holes on the sides. Is this easy to replace ourselves, and which part do I need to order?
1 Answer Ana, the right drawer end cap is part number W10874836. The end cap is held onto the wall of the refrigerator with screws. Just remove the screws and replace the endcaps. Thanks. Read More...
Bruce December 12, 2012 for Model Number KBFS25ETSS00 How to disconnect the temperature control arm from the shelf support right hand side for this model.
1 Answer Hello Bruce, To remove the control arm from the end cap you would first release the back portion of the arm by popping loose. You would then depress the tabs on below the arm and pull out. Once you have the arm out you have to turn the arm to get it off the control. Then pop control out and reinstall on new part. Read More...
1 Answer Hello Todd, To replace the Endcap you will first need to remove the pantry cover and drawer. Once you have these removed then remove the crisper drawers to make it easier to access. Remove the glass and cross bars that support the glass. Remove the metal rail on the endcap. There would be 2-1/4" screws that have to removed. Remove the 3-1/4" screws holding in the endcap. Once screws are removed then you will pull forward on the endcap then twist toward inside of unit to get the back brackets out. Reinstall in reverse. Read More...
Chuck October 28, 2012 for Model Number MF12569VEQ0 SERIAL # KY0617118 Maytag The wife broke both sides of the crisper door pegs. I need the part numbers for the drawer endcaps.
1 Answer Chuck, the left refrigerator drawer endcap is part number W10874836 and the right refrigerator drawer end cap is part number W10874836. Thanks! Read More...
Gary J. October 04, 2012 for Model Number Mayday MFI2569VEB2 It looks like I need to replace the end cap due to the peg holding the crisper door broke. My question is the left/right as you look at the open refrigerator or looking out from the refrigerator?
1 Answer Hello Gary! You will determine the side of the unit by looking into the refrigerator. For the right side use part number W10874836 and the left side use part number W10874836. Thanks! Read More...