Tz March 29, 2022 for Model Number MDBTT79AWW My dishes are not as clean as they used to be. I replaced the docking station because it was damaged and now I see that OV filter. Is that filter a part that needs to be changed at certain intervals? Thank You.
1 Answer Hello TZ, A difference in cleaning is normally related to a heating circuit issue. You should check the heating element, the high limit thermostat, the door switches, the door switches, and the control board. The wiring harness is another possible cause of the issue. The unit needs to be properly leveled and secured under the countertop for the door switches to "make" electrically. You can check for 120Vac at the high limit thermostat. If the voltage is only on one terminal, the high limit thermostat is bad. If there is voltage to both sides, it is fine and the heater should be checked for about 16O of resistance. If this is good, chances are that the control has failed. If the serial number begins with 18 or lower, I'm sorry but the part 99003160 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. If the serial number begins with 19 or higher you will need to order 12002709. Thank you for your patience and understanding in this matter. Read More...
Thomas January 19, 2018 for Model Number Jenn-Air JDB2100AWS I am having issues with this machine doing a good job. I have troubleshot the water fill and replaced the heater element. Still the upper rack does not always get clean. While looking at the schematic of the water system I see the over pressure filter is not installed on my machine. The part is not available anywhere. Can I plug the hole where it is supposed to be installed to increase pressure in my water system?
1 Answer Thomas, Unfortunately we do not have anything that would allow the hole to be plugged but if you are able to then you could plug it. Read More...
Duncan M. December 15, 2016 for Model Number mdb 9750 aws For some reason this dishwasher does not have a filter, overpressure. Maybe it has been discarded or there never was one installed. Is it necessary? I think it is because if I put the rotating arms in the same position and run a cycle, they don't look to have moved. This looks like lack of pressure to the arms.
1 Answer Hello Duncan, You are completely correct. The over-pressure filter W11032558 is necessary to maintain proper water pressure so the spray arms can operate properly. Read More...
Mike May 26, 2015 for Model Number JDB2100AWB Similar to Dave's question. My filter is not there and I have no water coming out of the 3 rotating spray arms. After a few minutes of running, if I open the door, the spray arms are not spinning. The water level is up to the heater. What could the problem be. I thought not having the filter created less pressure and that's why the arms weren't spinning.
1 Answer Hello Mike. You need to check and see if the impeller WP99002659 is stripped out, shaft is broke WP6-919539, or if the motor 6-919963 is bad and not running. Any of the 3 will cause your issue. Read More...
Dave May 11, 2013 for Model Number MDB7600AWB My question is similar to Henry's, but I need to know if not having this filter will affect the pressure in the top-rack spray arm. My filter is missing, and I think this causes a big drop in the pressure required to make the top spray arm rotate. My top spray arm appears to stay in one position for the whole cycle. Thanks, Dave from Clinton, MI
1 Answer Dave, No the filter will not affect the wash motion of the upper spray arm, in fact the filter was removed from later versions of this style dishwasher. If the upper spray arm does not rotate, you need to verify the water fill level in the bottom of the tub. Start and allow the dishwasher to operate for 5 minutes., unlatch the door and remove the lower rack. The water level should be 1/2 way covering the heater element(at least). If the water level is correct, you'll need to check to see if the detergent or the rinse agent is sudsing or foaming.If the water level is too low then replace the fill valve 99002628. Read More...
Henry June 30, 2011 for Model Number MDB5600AWB Would not having this filter affect the lower sprayer and it not spray?
1 Answer Hello Henry. No, the over pressure filter W11032558 should not cause the lower spray arm not to work. You will need to check and make sure the water level is correct inside the tub assembly. It should fill to the bottom of the heater. If it is not, you will want to check the float assembly and make sure it is not stuck. If it is good, you will need to replace the water valve 99002628. If the water level is correct, you will want to check the impeller assembly and make sure it is not clogged or broken. If it is broke, you may need to replace the shaft assembly WP6-919539. Hope this helps. Read More...