Rich K. November 16, 2012 for Model Number FRT21NGJD3 The front support tab on the crisper shelf has broken off. It appears that the shelf unit is all one piece. Can't locate the proper shelf replacement among so many repair sections and websites. My machine is serial number LA03825246. HELP! We get dizzy looking into fridge with crooked shelf! Thanks.
1 Answer Hi. Verify the Crisper Shelf Support Part Number: 5303288973. I believe it is what you need. Thank You. Read More...
Mkler August 10, 2012 for Model Number MFF2558VEW2 I am looking to replace the plastic supports for the crisper frame. The supports attach into the rail in the back of the unit and the crisper frame rests on the supports. I cannot find them on any diagram. The picture is somewhat small, but are the supports now built into the crisper frame? Do I need to get a new crisper frame?
1 Answer Hello! According to your model number the crisper frame support is part number WP13062602. Thanks! Read More...
Alfie May 31, 2012 for Model Number jf12589aep i am looking for the front part of the crisper frame that has like a plastic coating that says with humidity printing etc for vegetables and meat not the crisper frame itself Just the front piece what part number is it Thanks
1 Answer Alfie, You're needing the crisper shelf front trim W10231487. This is a "snap Lock" fitting, so you'll need to be careful when you remove and install the parts. Thanks and Good Luck Read More...
Edward May 17, 2012 for Model Number MFI2569VEB I am ordering the crisper frame AP4077914. I need to know if it comes with the two humidity controls installed or should I order them separately?
1 Answer Hello Edward! No, the crisper frame WP67003854 does not include the humidity control slide part number WP67005864. Thanks! Read More...
B February 04, 2012 for Model Number AFD2535FES After disassembling the interior shelves for cleaning, I am unable to find the place the brace for the drawers fits properly. Anyone know? Can't locate a diagram either.
1 Answer Hello B! Here is the link to the refrigerator shelving. Perhaps this will help you. Thanks! http://www.appliancepartspros.com/partsearch/frame_diagram.aspx?diagram_id=28596864&pkw_=basket&model_id=5173922&NewWindow=1 Read More...
Jw December 13, 2011 for Model Number Maytag MBF2562HEW The center support broke off at the front of the crisper frame and the small broken piece is in the crisper frame. Do I need to buy this frame (or another model, since I don't see my Maytag refrigerator listed below) and also the center support that allows the crisper drawers to slide open?
1 Answer JW, The center rail/support should be part no. WPW10326469, you'll need to "snap " it into place on the crisper frame after you remove the glass shelf. Also check and make sure the metal support rod / brace WP12642303WD is in place in the slot molded into the underside of the front area of the crisper frame. Thanks and Good Luck Read More...
Russell November 20, 2011 for Model Number jfd2589kes4 I need the center support for this part. It holds one side of each crisper. It is not pictured here. What would be the part number for it. Thanks
1 Answer Russel, Apparently there is an issue with the publication of the parts diagrams. The part you need should be WPW10326469 . We were able to find it under a different model number that uses the same crisper shelf, so it should work in your unit. Good Luck and Thanks Read More...
Mojne M. July 27, 2011 for Model Number 59676573602 How do I remove moving parts from this frame? How do I attach these parts back? Thanks
1 Answer Hello Mojne. Here are the instructions from the manufacture. Hope this helps. Crisper Top The crisper top serves as the lower fresh food shelf. To Remove the Crisper Top: • Remove crisper drawers. • Place hand under the frame to push up the glass. Lift glass out. • Lift frame from refrigerator liner rails. To Install: • Replace frame in refrigerator liner rails. • Carefully replace glass into frame. Read More...