Jane November 18, 2013 for Model Number JennAir JCD2389dt My icemaker will not fill the ice tray. The water supply lines are clear as is the fill tube. Water dispenses through the door. What part needs to be replaced?
1 Answer Hello Jane. Make sure the freezer is between 0° and 5°. You need to check and see if there is power going to the water valve when the icemaker cycles. If so, replace the water valve on the unit. If not, or the icemaker does not cycle, you will need to replace the icemaker on the unit. Also, check and make sure the fill tube on the unit is not frozen and clogged. If so, replace the water valve and thaw out the fill tube. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Greg October 22, 2013 for Model Number Gx5SHDXTQ00 My ice maker was working fine, but was leaking along the front edge (metal was corroded). I purchased a new icemaker (Part # AP4135008), unplugged the refrigerator and installed the new icemaker. And nothing... there is no water filling the icemaker, the ejector arms are not moving, the shut off arm is in the down position. It is as if there is no power to the icemaker. I just took the icemaker back off, rechecked the electrical connections and still nothing. Any ideas? Is there any way to test the unit?
1 Answer Hello Greg. The unit has to get cold before it will cycle. Leave it in there and it should make ice in 4 to 6 hours. Read More...
Part D7813010 Ice Machine Wiring Harness May 23, 2013 I need to know what kind of fusible link is run in this wiring harness.Thank you. b
1 Answer The fuse in the icemaker harness is a thermal fuse that opens when if the icemaker heater has stayed on for too long. Read More...
Laurie November 20, 2012 for Model Number ATF1910DR My icemaker stoppoed working. I tried defrosting it because water was not coming out. I also poored water into the tray and let it freeze but it has not dumped out the ice yet. Should I replace the pump or the icemaker?
1 Answer Hello Laurie. If the water that was poured in did not dump, you will need to replace the icemaker, not the water valve on the unit. Read More...
K.C. June 06, 2012 for Model Number amana scd25tw How do get the wiring harness off of the ice maker? No plug by the ice maker. The wires go into the back of refrigerator.
1 Answer Hello K.C., Remove the white plastic cover from the front of the icemaker assembly. It just snaps on. Once this is off, turn the icemaker and look at the side where the harness connects. On the side of the icemaker there is a small square hole where you can see the plastic molex connector that plugs into the icemaker. Using a small screwdriver, press in on the side closest to the wires. As you do this, pull on the harness and it should slide right out. It will insert without the use of any tools. Read More...
Rand February 09, 2012 for Model Number ASD2620HRB The first wiring harness (Ap4427021) I ordered for the new ice maker I am installing is 1" too short. So I ordered wiring harness AP4325036, as per your advice, and it is 2" too short. Your company says these should fit. Do you stock one that is longer?
1 Answer Rand, the icemaker harness used on your model ASD2620HRB should be part number W10146387. Thanks. Read More...
Randall January 28, 2012 for Model Number ASD2620HRB Hello, the wiring harness that is for my model ASD2620HRB is too short, the harness plus in ok, but when I go to install the ice maker, it is about 1 inch too short, what should I do in this situation?
1 Answer Hi Randall. The ice maker wire-harness for your unit is part # W10146387. Please call A.P.P. Customer Service @ 1-877-477-7278. Thank You. Read More...
Don January 14, 2012 for Model Number MBF1956KEB installed water to ice maker but cannot get power to solenoid
1 Answer Don, The first thing to do is unplug the power cord and tape the freezer drawer light switch closed. disconnect the wires at the fill valve and attach the meter leads to the wires. Using the jumper wire, insert the ends into the "T" and "H" openings in the control head and check for 120 VAC at the wires, when the rake arm reaches the 1 to 2 O'clock position, Good Luck and Thanks Read More...
Leland S. January 04, 2012 for Model Number AP4135008 I installed the part. Some reason it did not work. I have plugged in on each end of the electrical attachment.
1 Answer Hello Leland. If you replaced the wiring harness WPD7813010 and the unit still does not work, you have another problem other than the wiring harness. Hope this helps. Read More...
Grant August 15, 2011 for Model Number JCD2290HES How do you remove the existing plastic tubing water lines on the water valve and install the tubing in the new valve? Thank You
1 Answer Hello Grant. To remove the water lines from the water valve WP67005154, you will press in on the plastic fittings, and pull the water lines out of the water valve. To install the lines, you will press them into the fittings until they bottom out and lock into place. Pull on the line lightly to make sure the are secured. Hope this helps. Read More...