Charles November 09, 2019 for Model Number Whirlpool drain hose wp40053901 On the drain hose, there are a couple of "flat spots" and I wonder if those are the only places to use the brackets? It seems to me that if I use the flat spot nearest the drain pump, the hose is so long that it gets kinked (black rubber portion) between the drain pump and the bracket. Is it okay to secure the brackets anywhere on the hose that allows me to avoid that, or does that prevent me from securing the hose fully? Thanks!
1 Answer Hello Charles, the hose areas where there are no ribs are there is the hose needs to be shortened or lengthened, the u-bend bracket goes anywhere on the hose length, the end should go just about 6 inches into the standpipe to avoid siphoning. Read More...
Andy November 14, 2015 for Model Number WFW8500SR0 I could not find my model WFW8500SR00 in your list (it is Canada made). Could you confirm that your part 40053901 will fit my model. Thanks.
1 Answer Hello Andy, The part shown by the manufacturer for the model provided is WPW10114608. The part you were viewing is not on this models' parts list. Read More...
Bob March 17, 2015 for Model Number whirlpool wtw8500dc0 I need a 7' drain hose. I cut my original hose so the extension kit don't work and its close to the wall so I need the one with a 90 on it
1 Answer Bob, we can only suggest the replacement specifically for your model. The replacement is part number WPW10363893 and the extension is part number DRNEXT4. Thanks. Read More...
Adrian Z. March 23, 2014 for Model Number Amana Washer PLW3502L2 I have to replace the drain Line of my washer and I already have the replacement part, but the pipe is inserted right into a hole in the backpanel and I am afraid to pull it out and damage any part or holding bracket or something. Do you know if its OK to pull it and then just push the replacement in place or is there something you recomend I do instead? Thanks for your advise!!!
1 Answer Adrian, The drain hose WP40053901 connects to the drain pump 27001233 located at the front of the machine. You will need to remove the front panel of the washer(two/2 screws) and loosen/remove the hose clamp, then slide the hose out the back of the cabinet. Then reverse the procedure and test the washer for leaks and operation. Read More...
Bogeyman January 27, 2014 for Model Number SAV515DAWW Re: drain hose (40053901) - what is the diameter (inside) of the connecting end of this hose?
1 Answer Hello Bogeyman! Unfortunately, we do not have the information requested. However, according to the model number supplied this is the original hose used on your model and will be the same as the current hose. Thanks. Read More...
Richard June 15, 2013 for Model Number Whirlpool lsn2000pg3 I need a longer drain hose or a way to extend it.
1 Answer Richard, There is a 4' drain hose extension kit part number 285863 to use for your unit. Read More...
Randy May 21, 2013 for Model Number Kenmore model 417.92702200 I am looking for a drain hose that will replace the one in this model.
1 Answer Alex, may I have the appliance model number please? We will need your model number to verify the correct hose used on your unit. If you do not have the model number available locate our main page, select "Washer Parts", then on the left hand side on the Narrow Your Choices section click on "hose or tube". Hope this helps you. Thanks! Read More...
Brian I. June 15, 2011 for Model Number amana #LWA40AW2 Do they make a longer one or an extension? Thank you.
Tom Z. April 12, 2011 What is the lentgh of this hose. I need 6' and would like a maytag or whirlpool product.