Ronald B October 29, 2016 for Model Number 10650443909 My ice maker stopped producing ice a few days ago. It may be coincidence, but after having to repair a damaged hot water heater I noticed that the maker was not filling or making ice anymore. I thought maybe during the draining and flushing of my water heater that the maker inlet valve got air locked. Meanwhile the water dispenser works fine. I pulled the ice maker out and used a test jumper between T & H on the control board and the maker would cycle through it's fill & dispense operation. So, no air or frozen lines. After reinstalling the unit still no ice. When I open the freezer door, the emitter light flashes 2 times then a pause and repeats. Upon holding the flap down the light stays on solid. Would this indicate that my ice maker is defective? If not, any further troubleshooting advice would be awesome!
1 Answer Ronald, You will want to pull the icemaker and take the module off the front and see if there is a burn mark on the connection points. If there is then replace the icemaker. If there is not then the issue will be with the water valve. Read More...
Jack June 02, 2014 for Model Number MSD2559XEM03 Water runs out the ice cube maker and all over the inside of the freezer.
1 Answer Hello Jack. If the icemaker is overfilling, replace the water valve WPW10179146. If it is leaking, replace the icemaker W11512152. Read More...
Rick April 29, 2014 for Model Number ksrl25fxms01 How do I know if its the ice maker or the water inlet valve that's bad? I have water to valve and drinking water , But not to the ice maker.
1 Answer Hello Rick. Here is a link to our Repair Forum, this is a free service to our customers. Use this link to access the repair for your question. http://forum.appliancepartspros.com/refrigerator-freezer-repair/29618-ice-maker-not-working-kitchenaid.html Read More...
Brent October 16, 2013 for Model Number KSRJ25FXWHO1 Kitchenaid fridge Is this ice maker complete, just remove old and install new one? The module part #W10272870, or motor mold is included? Do I have to remove parts off the broken one and install them on the new one?
Marty August 30, 2013 for Model Number kenmore elite #10654789803 My ice maker will produce ice and some days just stop, the food n the shelfs below and the inside of door is covered with ice? What should I do ??
1 Answer Marty, You will want to check the fill cup on the icemaker to see if it is frozen over with ice. If it is then you need to clean it out and replace the water valve due to seeping water and dripping into the cup and freezing. Read More...
Leo January 12, 2013 for Model Number WPL W10300023 ice maker for Kenmore Elite refrigerator I purchased this part for my refrigerator and after installing it, it didn't work. Was there something I needed to do to the unit before installing? The icemaker didn't fill with water. On the inside panel of icemaker it says to put ejector blades at 2 o'clock position, how is that done without rotateing manually?
1 Answer Hello Leo, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Stephani January 02, 2013 I purchased this icemaker. I do not have the "on/off" bar in my freezer as it has a laser beam. Is there something I need to do to this part to keep it in the "on" position? It appears as if it is in the Off position. It has been in the freezer for 48 hours and is not making any ice. I tried turning the inside nozzle with a screw driver, and it goes into the "on" position and I hear a small change in it, but it will not stay in that position.
1 Answer Hello Stephani, The little position place that you are turning should be in the down position. You may want to look at your emitter beam to make sure that it is functioning properly. When looking at the light on the right side where the beam would be, the light should be flashing. If not then push on door switch and on the flapper and see if it is a quick flashes. If there is no flashing then you have a bad emitter board W11629974 and would need to be replaced. If it is flashing with door open and then you push on the flapper then it should glow solid. If not then the emitter board is bad and would need to be replaced. Read More...
Neal Z. October 08, 2012 for Model Number KSRL25FXBL03 Is this the right ice maker for me and does it come with all the parts shown?
1 Answer Hello Neal! Yes, the icemaker W11512152 is the correct replacement used on your refrigerator. It does not include the valve and tubing, this is the icemaker assembly only. Thanks! Read More...
Don August 05, 2012 for Model Number W10300023 I have a Kenmore Elite fridge # 106.54782802 which this ice maker is suppose to fit. Ice maker # W10300023. My question is, is this a complete ice maker? It says this is part number 100 in diagram but there is no # 100.
1 Answer Hello Don! Yes, the icemaker W11512152 is the complete icemaker assembly and is the correct replacement used on your Kenmore refrigerator model 106.54782802. Thanks! Read More...