Erica February 16, 2022 for Model Number 5789A602-60 lp conversion kit Hi, I'm looking to purchase an LP conversion kit for a maytag gemini stove i bought second hand (it's set up for nat gas and I have propane). The conversion kit is 5789A602-60 but it's discontinued and I can't find it anywhere. Is there a way to find the measurements of the orifices to get other pieces that would fit? When I bought the stove, I didn't realize that conversion kits weren't universally sized.
1 Answer Erica, unfortunately, the manufacturer does not indicate the exact measurements of the orifices used in the discontinued kit WP5789A602-60. Read More...
Cowboy November 20, 2014 for Model Number MGR6775BD17 We are trying to find out what to do to swith our range from LP back to gas, cannot find any orfices in stove.
1 Answer Hello! You'll need to purchase the orifice holders. For the left front use part number WP7527P021-60, left rear and right rear use part number WP74007961, center use part number WP7527P023-60, an right front use part number WP7527P028-60. Adjust the oven orifices and flip the regulator back to NG. Thanks. Read More...
Greg I. September 03, 2011 for Model Number mgr6875adb26 maytag dbl oven If you look the kit shown, it shows 2 large graces and 7 small. I have a dbl oven w/ a broiled so I have three oven burners. I understand why you are saying about the regular by this one has nothing to flip. Sometimes you cm it an insert to change. The pressure or inverted the cap, this regular he's neither. Or any disable way to adjust. Help, please. 317 339 0118
1 Answer Hi Greg. Have you carefully followed all instructions included with the kit ? You will need to convert the pressure regulator cap by flipping it over and making sure the actual cap cover will remain all together as same as removed (just holding with the cap threads also). Making sure as you lift the cover it will tell you what gas you have just converted to. By going to LP, you adjust all bake and broil burners down approx. 2, 2-1/2 full turns until fully bottomed out. Open the shutter windows all the way open as it will need more air. Then adjust accordingly until bake / broil burners have no yellow tip or very little tipping. The same rules follow on the top burner orifice's. You use the exact ones supplied in the kit for the correct burner. Then you warm up a burner for at least 5-minutes you need to adjust in case of lift off or yellow tips. You will use a very long small blade to remove the knob and adjust the burner in question with a pan of water on the grate. The burner should just "cap over" the top of the burner assy. on the lowest setting. If the instructions supplied with the LP kit is worded differently then follow the instructions closely to your kit. Thank you. -- Read More...
Greg I. September 03, 2011 for Model Number mgr6875adb26 The oven offices are larger than those remaining and the regulator has no switch for lp or natural gas. Help again please
1 Answer Hello Greg. You have to remove the cap off the regulator to flip the regulator to LP. The orifices in the kit WP5789A602-60 are designed to convert the oven as well as the cook top. They should fit the burners in the oven. Hope this helps. Read More...
Greg I. September 02, 2011 for Model Number mgr6875adb26 Maytag gas range I bought this kit and it had seven small orifice's no large nor instructions. I need help to convert it to LP. The burners are fine after changing the orfice's now I need to know how to convert the three oven burners. and do I need to do something to the regulator? PS I have been trying to get this done for several weeks now. Help, help !!! Thanks, Greg 317-339-0118
1 Answer Hello Greg. You should have two orifices left, if you have changed the top. One installs on the bake burner and the other on the broil burner inside the oven. You will need to remove the cap on the regulator 74007387 and flip it from natural to LP gas. Hope this helps. Read More...