Doer December 22, 2017 Whirlpool microwave wmh3101fw-0: How to remedy delayed start of replacement interior light bulb (westpoint 40w/s11/e17/440 lumens/ intermediate base)?
1 Answer Doer, The correct bulb for your unit would be part number 8206232A and if you put this bulb in then the control board would be causing the delay. Read More...
David S. December 16, 2017 for Model Number JKP27 ODIAD I have an older GE upper & lower oven. I replaced the light bulb in the lower oven it was a 40 W appliance bulb. When I put it in the light got extremely hot immediately and the off and on switch on the lower oven won't cut it off.
1 Answer Hello David, We will need you to please verify the model number on the units' I.D. tag and post a new question including this information so we can pull a wiring diagram since this sounds like there is a wiring issue with this unit. Thank you for your patience and understanding in this matter. Read More...
Sam May 02, 2017 for Model Number JTP15B0A1BB I have been having lately to change this wall oven appliance lights frequently (in less than two months from its replacement). I have purchased I believe the right appliance bulb from Home depot which is rated at 40W and installed accordingly. Any ideas why it is burning out so frequently. We normally don't leave the light on for any extended period of time or run the oven at extremely high temperatures. Appreciate any help u can offer.
1 Answer Sam, It would be suggested to check to make sure that there is not a voltage issue to the light bulb. Also make sure that the light is tight and make sure that there is no loose connection at the socket. Read More...
Tris March 27, 2017 for Model Number RS663V Hi. The freezer light has gone in my Westinghouse Fridge-Freezer. You have a replacement lightbulb in stock. Can I use that bulb in either the freezer section or is it just for the fridge section? Do I need a different lightbulb in the freezer section? I've never had to change one before and want to make sure I get the right part. Cheers!
1 Answer Tris, This bulb should be able to be used in either the refrigerator or the freezer section of the unit. Read More...
Jim B March 25, 2017 for Model Number R H 758 OT 1HT I have an old oven top oven and the light bulb went out and I can't figure out how to replace it without tearing apart the entire top frame. Any advise?
1 Answer Jim, For the oven light you would unscrew the cover of the bulb and should be able to remove the bulb. Read More...
Narinder March 16, 2017 for Model Number Whirlpool Is there is special bulb for refrigerator or you can change it with any 40W bulb.
1 Answer Hello Narinder. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
1 Answer John, Check the oven light receptacle, make sure it's not too loose in the oven cavity. make sure you use a brass based 40 watt appliance bulb or the 8009 light bulb, apply a thin coat of dielectric grease to the threads of the bulb, and the glass lens cover, and dont overtighten the bulb in the receptacle. Read More...
Guy March 03, 2017 for Model Number WFC150M0EW0 Hi, I'm trying to replace the oven light bulb however, I'm finding it difficult to remove the lens cover. Please help. Thank you
1 Answer Guy, The Light lens should just unscrew. You may need to get something to grip the lens to get it to twist off. Read More...
Mike January 08, 2017 for Model Number RK7660P3WH I have a Hotpoint double oven that is probably original to the house. Mid 1970s. Still works fine but the upper oven bulb is out. The outer bulb protector spins in my hand rather than coming out. How do I get that out to change the bulb?
1 Answer Hello Mike. Try pulling out on the lens while you turn the cover to see if that help you to remove the lens. Read More...
Lee K November 12, 2016 for Model Number MTB2156DE* Maytag A bulb in the refrigerator has burned out. The bulb is protected by a plastic cage which does not seem to be removable. I have been able to remove the bulb but screwing in a new one has been a challenge. It seems to cross thread every time. The bulb is a GE 40 w appliance bulb. Is the cage removable for easy access to the socket or do I need an OE bulb?
1 Answer Lee, Yes the cover will come off as it has hooks on the side where you have to squeeze in on it to get it to release. Read More...