Mary October 27, 2012 My lower agitator is not spin drying. I recently moved into a house where there was a washer being used that was purchased overseas. My dryer works fine but washer does not spin dry. Could it be the voltage. My o-ring is broken I noticed also but it still agitates.
1 Answer Hello Mary, We will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Texasmom October 26, 2012 for Model Number LSWB6400LW0 What size cam do I need for the agitator on model lsb6400lw0?
1 Answer Hello TexasMom! Your model LSB6400LW0 uses the short cam agitator repair kit, part number 285809. Thanks! Read More...
Texas Mom October 26, 2012 for Model Number LSB6400LW0 What size cam do I need for model # LSB64006W0?
Cliff October 18, 2012 for Model Number LSR7233EQ You have short, medium, long cams listed for agitator repair kit. Which one is for my particular model.
Angela1597 October 16, 2012 for Model Number LSR7333PQ4 At the end of my washer cycle it stopped. It smelt like rubber and would not finished the cycle. Their is no oil anywhere and the only part that fell out of the bottom was ap2905299.
1 Answer Hello Angela1597. You will need to check and see if the motor coupling 285753A is bad and needs to be replaced on the unit. Here is a video link to help you do this. http://www.youtube.com/watch?feature=player_embedded&v=MYB5x-IqtIM Read More...
Elizabeth September 11, 2012 for Model Number Whirlpool LRS6132EQ1 I removed the entire agitator assembly. It appears that the thrust washer tabs are worn, and the agitator dogs broke. Every thing else looks good and cleaned up well. Except that I could use the washer. Is there anything I might be not seeing? Are the parts I see the right ones for my model? I don't see my model # (for a 1997 Whirlpool) on the list. Thanks!
1 Answer Hello Elizabeth. Based on the information you provided, you will need to order and replace the cam kit 285811 in the unit. Read More...
1 Answer T.Gale, There are several reasons and scenarios. If the washer isn't draining or spinning, you'll need to check the lid switch 3949247V and timer 3950705 . If the washer motor runs, and drains the tub, then you'll need to check between the tubs for an article stuck between them, A slipping clutch 285785 and or damaged coupler 285753A. Read More...
Brenda August 29, 2012 how to stop a maytag top load washers agitator from unscrewing itself. I can find the model #
1 Answer Brenda, If you have a "MAV" model, you will need to check and replace the agitator screw WPW10309247 which is located in the center of the agitator, under the cenetr cap or rinse aid dispenser WP22004042 . If you have a "LAT" model, the agitator is secured to the agitator shaft by a 1/4 inch hex head screw located near the bottom or the agitator "barrel' and cannot "unscrew" itself WP207228. Either way, you will need to check and make sure you're not overloading the washer, and or the water level(s) are correct. Thanks Read More...
Brenda August 24, 2012 for Model Number gsx9750PW0 Now I am asking how I can check the belt to see if it the belt? When I put the agitator back on it spins freely. Could this be the belt?
1 Answer Hello Brenda. This model does not use a belt. You can check and see if the motor coupling 285753A is broke and is causing the issue you are having with the unit. Lean the washer back and check between the motor and the transmission to check the coupling. Read More...
Lloyd August 23, 2012 for Model Number Whirlpool lsq9544kt0 The clothes mover isn't working right. Should I just replace the "dogs" or replace the dogs and the clothes mover? The teeth on the clothes mover don't look real good (but I don't know what they are supposed to look like). Also, I saw in a couple of posts something about applying grease to the teeth.
1 Answer Hello Lloyd. Usually, you just need to replace the cam kit 285811 and not the whole agitator. You shouldn't need any grease. Read More...