John September 03, 2013 for Model Number KGRT607HBS6 The gas range will act like it wants to turn on by itself, a beep will sound like some one is turning it on. I will turn it off and it will beep and turn on again without anybody touching the stove. Thank you
1 Answer Hello John. It sounds like the control board is bad and will need to be replaced on the unit. Read More...
Bill V August 19, 2013 for Model Number kesc307hbt6 The beeper/sounder/alarm does not beep/sound/alarm. Everything else works.
1 Answer Bill, With the alarm not sounding then you will want to make sure that the tones is not disabled. To do this you would To Enable/Disable Tones: 1. Press CANCEL OFF. 2. Open oven door. 3. Press and hold STOP TIME for 6 seconds. 4. Display will show “SND ON” or “SND OFF. Read More...
Dwight June 24, 2013 for Model Number KGST307HBS6 When using oven the F1 E3 Fault Name appears and range will not work. I clear it by turning off power and restarting. It will work for a time but usually cuts out again. Manual states configuration mis-match, configuration jumper change. Jumpers have not been changed, nor has unit been worked on in years. I would greatly appreciate any help you can provide.
1 Answer Hello Dwight. It sounds like the microcomputer is bad and will need to be replaced on the unit. Read More...
Gina Wesley February 11, 2013 for Model Number ykgrt607hwh9 i was given this stove from a friend and it had no troubles. i have used it for aprox 2 months with no problems. the other day i went to use the oven and it started to heat up and went blank on the display. i started it again and it did the same. now its all blank but the oven light continues to work . the range top works and the clock keeps time .i spent alot of money to put in gas line in and not sure what to do at this point. my brother can check stove parts if he knew how and what to check.i see it could be the display board , the console or the microboard. i dont want to replace all of them or just guess at which one .please help. thank you .
1 Answer Hello Gina, You would want to check the wiring from the display board to the control board. If this checks ok then you would want to replace the power board. Read More...
Dave December 08, 2012 for Model Number KGRT607HBT How can I tell if I need to replace the console or the microcomputer? The stove has power but we cannot see anything on the display.
1 Answer Hello Dave, You can check from P4 to J1 pin 1 on the control board to make sure that you are getting power to the board. You should have 120 vac between these 2 terminals. If there is no power then you would want to check to make sure you have continuity through the thermal fuse WP341196. If no continuity then thermal fuse is faulty. If no continuity then the control board 3191106 would need to be replaced. Read More...
Rami November 14, 2012 for Model Number KGRT607HBT6 During the last storm we kept losing and getting the electricty back and finally after we got it back the stove started pressing the buttons by it self so I had to lock the control panel. Is the control panel dead? or is there something else?
1 Answer Hello Rami. Based on the information you provided, it sounds like the console 9754341CB is bad on the unit, not the microcomputer. Read More...
Florida_Sara January 08, 2012 for Model Number KESC307HBL6 On the touch panel of the Kitchen Aide stove the numbers 1, 4 and 7 do not work. What is needed to to repair this?
1 Answer Hello Sara. You will need to replace the console assembly 9754342CB on the unit to repair the numbers. Hope this helps. Read More...
Marcelino December 12, 2011 for Model Number kgst307hbs6 I can not see light from the microcomputer on any more. What could be the problem?
1 Answer Hello Marcelino. If there is power coming to the microcomputer and there is no display, you will need to replace the microcomputer 8184718. Hope this helps. Read More...