Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Dryer Drive Motor by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM18019167
Manufacturer Part Number: WP2200376

Fix a dryer that hums but won't turn with a new drive motor. This repair addresses seized bearings and worn motor assemblies. Moderate DIY project.

More
$120.56

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Dryer Drive Motor (Part Number: OEM18019167)

Stuart for Model Number MDE508DAYK

Hello We have had the Maytag MDE508DAYK dryer for about 10 years. About 2 years ago I replaced the drive belt and idler pulley as the pulley seized and destroyed the belt. Now after the dryer runs for a bit it starts to make a loud buzzing or humming noise. The sound comes and goes, it is not continuous. It lasts for a few minutes and then goes away and then comes back a few minutes later. I disassembled the dryer and checked the rear rollers and the idler roller and all run smooth. I also cleaned out all of the lint in the machine and removed the motor and used a compressor to blow all of the lint out of the motor. The problem persists. Motor going bad? Or something else? Thanks

1 Answer

Stuart, First check the blower wheel 56000 and make sure none of the vanes or the front frame are cracked or broken, make sure there aren't any small articles stuck or wrapped around the wheel or motor shaft, If all's OK then replace the motor, sounds like the motor shaft bearings are worn and starting to make noise.

Read More...

1 Answer

Hello Jim. Yes, based on the information you provided, the motor is bad and will need to be replaced on the unit.

Read More...

1 Answer

Dom,

If the motor pulley is spinning freely on the shaft of the motor then this will require the motor to be replaced. The part number for the motor is WP2200376.

Read More...
Matt for Model Number Mde4658ayw

I replaced the drive belt and drum wheels on my dryer. It worked for about 10 minutes and then I heard a bang and the drum stopped turning. When I took it apart, I found the main pulley on the motor was sheared in half. (I assume the belt wasn't properly aligned and put stress on the pulley?) Your site indicates that the pulley isn't available as a stand alone part because it's pressed on the motor shaft. However, mine was screwed onto the shaft. I unscrewed half of the broken pulley by hand from the shaft to remove it. Is there a part available that could be simply screwed back onto the shaft or no? Thank you in advance!

1 Answer

Hello Matt! Unfortunately, the manufacturer does not offer the pulley separate from the motor assembly, part number WP2200376. Sorry about that!

Read More...

1 Answer

Hello Steve. Disconnect power. Remove the lower access panel. Open door and remove lint filter. Remove screws securing the bulkhead to the panel. Disconnect wires from heater and thermistor. Remove the belt from the motor and remove the drum. Unplug wires from the motor. Remove the screws securing the motor bracket to the base of the unit. Pull forward and disengage the exhaust duct. Rotate and slide the motor assembly out of the unit. Remove the cover and the blower wheel from the motor. Pry off the clamps and replace the motor.

Read More...

1 Answer

Hello John,
The front panels will have to be removed and the main top raised. The drum is then removed and the motor is accessed. We can send you some illustrated instructions if you could re-post with a valid e-mail address.

Read More...
David for Model Number SDG4000AWW

I replaced the motor in my maytag SDG4000AWW. Now the turn-on-push-switch has to be held in place for it to work. In other words as soon as I let off the switch the dryer stops. Also, it is not putting out any heat even if I hold the button in for a few minutes. Do you think the push switch is bad? There was a sock stuck in the vent and people in my house continued to push the switch to try and hope the dryer would start, but the motor got hot. Maybe switch got hot too and is now defective. Whatelse could it be? Thank you!

1 Answer

Hello David,
If the motor is wired correctly, the centrifugal switch in the new motor is bad.

Read More...

1 Answer

Mike,

Unfortunately the pulley appears to be pressed onto the motor shaft of your unit and cannot be replaced. You would have to replace the motor assembly WP2200376.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google