Rk March 14, 2012 for Model Number CRE9400ACE The oven takes longer to bake food than it did about a month ago. The oven goes to the temperature set point and the bake element is getting red and hot. It seems to reach the set point temperature in a reasonable time. Why the poor performance?
1 Answer Hello RK. You will need to check and see if the temperature in the oven is correct. Test it with a meter with temp. If not, you can test the oven sensor 12001656 and see if it is bad. It should read around 1100 ohms at room temperature and 1650 ohms at 350°. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Roquemore March 09, 2012 for Model Number AER5715QAW It takes up to 2 hours for the oven to reach 350°. I don't know if it's a heating sensor or a heating element.
1 Answer Hello Roquemore. I think it's probably the thermal limiter 74008715. It is located on the back of the unit. You need to disconnect power from the unit and remove the main back. It will have only 2 wires going to it. I hope this information helps you out. Have a great day! Read More...
Al March 08, 2012 for Model Number AER5845QAS The oven temp is all over the charts. I set it on 200 and it goes to 350, I set it on 350 and it goes to 450. Would that be the temp probe?
1 Answer Hi Al. You need to pull out the oven and remove the back. Then you need to use a volt/ohm meter part # MA-DM1 to see if the sensor ohms out to 1080 -1100 ohms. Move the wires around to see if they are shorted or open. If it is out of 10% tolerance values then replace it with part # 12001656. Is the unit showing codes ? Thank You. Read More...
Tom March 01, 2012 for Model Number 3868XVA My oven take about 45 min to an hour to reach 200 degrees. Keep klicking as temp trys to climb. Thanks for your help.
1 Answer Hello Tom. Test the bake element WP74003019 and see if it is bad. It should read closed for continuity. If it is open, replace the element. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Hiltonraider February 27, 2012 for Model Number cwe 4800 acs I just purchases this oven and not sure it is operating properly. I put the boiler on 500 degrees for 5 minutes but the fan never comes on. I has a previous maytag oven that I purchased twenty years ago, and the new one when compared side by side with the old is identical .The older ovens fan came on as soon as the oven was set to bake,broil, clean. Also older oven has a metal wire from the back of the oven to the box on top (rear of oven).New one doesnt. Possibly a temp sensor. Any info appreciated. Dave
1 Answer Hello Hiltonraider. The fan W10127321 should turn on when the unit is turned on a baking or broil cycle. If the fan is not running, you will need to test for power to the fan motor. If there is power there, and the fan does not work, you will need to replace the fan motor in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Tony February 11, 2012 for Model Number Maytag CRE9600ACW My oven is not heating to the proper temperature. I tested the oven sensor and it is reading 1074 ohms. One of your previous responses states that the sensor should read 1085-1100 ohms. Is the slightly lower reading enough to cause my problem or should I look into another cause? When I set the oven to 350 degrees, and measure the temperature using an oven thermometer it reads 330 degrees. Setting the oven temp. to 400 degrees reads 360 degrees.
1 Answer Hello Tony. No, the sensor 12001656 is fine. You will need to test the oven temperature over about a 20 minute peirod. Then take the readings the oven turns on and the oven turns off add together and divide by 2. This will give you the actual temperature of the baking cycle. If the oven is off by 30°, you can calibrate the clock in the unit. Hope this helps. Read More...
Greg January 26, 2012 for Model Number MER6872BAW My lower oven would heat VERY slowly, so I replaced the bake element. No change in performance, and it still clicks trying to go to the next temp level. What are your suggested next steps?
1 Answer Hello Greg. Check and make sure the wiring is good. If so, it sounds like the clock assembly WP5701M406-60 is bad and will need to be replaced. Hope this helps. Read More...
Jack January 15, 2012 for Model Number JENNAIR RANGE SCE30600 AFTER SELF CLEANING THE OVEN DOOR WILL NOT UNLOCK AND THE FAN STAYS ON. THE LOCK LIGHT STAYS ON. DISCONNECTING THE POWER DOES NOT CORRECT THIS. I TRIED TO REPROGRAM THE SELF CLEANING CYCLE AND GET A F3 ERROR CODE. COULD THE OVEN SENSOR BE THE CAUSE? IF SO, CAN I REMOVE IT FROM THE BACK SINCE I CAN'T OPEN THE OVEN DOOR? THIS UNIT WAS OPERATING FINE PRIOR TO THE SELF CLEANING.
1 Answer Jack, yes, you could move the unit out of the cabinet, remove the rear cover panel and disconnect the sensor harness, attach the new sensor and program the range, once the door unlocks you can complete the proper install from the oven cavity. You may also want to try and manually unlock the door. Straigten a coat hanger and make a 2 in hook in one end. insert the hooked end from the left side of the door along the top edge, slide it to the right until you hear or feel the hook, slide over the latch assembly. Slightly push in on the door and pull to the left on the coat hanger at the same time(it only take a 1/4 inch or so to move the latch arm enough to open the door. Either way, Good Luck and Thanks Read More...
Benjamin January 12, 2012 for Model Number mer5755qaw My oven broiler started coming on randomly. I turned the power on and off. Now the oven display panel show CAL and none of the touch pad buttons respond. I tested the elements and they are good. The thermostat is only showing 600 oms of resistance. Do I need to replace the thermostat or is my control panel bad?
1 Answer Hello Benjamin. You will need to replace the oven sensor 12001656 if the ohms were 600. As for the control, this could be cause by the sensor, but if you replace the sensor, and the problem is still there, you will need to replace the control WP5701M717-60. Hope this helps. Read More...
Mike W. December 30, 2011 for Model Number PERL451ACW In Bake mode the internal temp. will only grt to 220. The unit clicks as it is trying to get to the next temperature but it does not increase. Is it the sensor ? The elements look intact?
1 Answer Hello Mike. Test the bake element WP7406P438-60 and make sure it reads closed for continuity. If not, you will need to replace the element. They can look good, but test bad in a lot of cases. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...