Barry December 07, 2011 for Model Number 9495vrv where do I find the temperature sensor and how do I remove it. I don't see anything that looks like a sensor inside the oven.
1 Answer Hello Barry. The temperature sensor 12001656 is located inside the oven on the back wall. Most have a screw on the inside to remove and the sensor pulls out. If there is no screw on the inside of the unit, you will need to remove the back panel to access and replace the sensor. Hope this helps. Read More...
Henry December 01, 2011 for Model Number 68HN-6TVW The oven does not come up to set temp. I've changed the oven sensor. The baking element comes on and glows nice and red. Where next do I look for this problem?
1 Answer Hello Henry. If the sensor is new, then the clock assembly 7601P178-60 is bad in the unit. This part has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Thanks. Read More...
Doug November 28, 2011 for Model Number mer6555aab We have a double oven.Both broilers work.Will not bake.I checked the elements they are good.Is this the sensors?
1 Answer Hello Doug. Look for a loose or burnt wire. If the wires are good, and the elements are good, replace the control W10769079. Hope this helps. Read More...
Dave Q. November 16, 2011 for Model Number D156 Dave, Did you have a "F?" error code in the display ? The oven temp. sensor should have a resistance of 1050 to 1100 ohms resistance at room temperature(78 dgrs.) and should have given you a F2,3,or 4 error code, had it failed. I can't help but think you may have a faulty relay board or ERC/Control, If they do not communicate with each other, the oven will shut down. AP4284826 AP4284825 Good Luck and Thanks I do not have any error codes and my ohms are 1100 on sensor. Is there any tests that I could run to find out which one of the above parts you mentioned are bad ? Thanks, Dave
1 Answer Hello Dave. Based on the test you performed, you have narrowed it down to the clock Y04100262 on the unit. You will need to replace the clock assembly. Hope this helps. Read More...
Dave Quill November 11, 2011 for Model Number D156 Oven comes on says pre-haet 140 degrees runs for about 15 seconds then shuts off
1 Answer Dave, Did you have a "F?" error code in the display ? The oven temp. sensor should have a resistance of 1050 to 1100 ohms resistance at room temperature(78 dgrs.) and should have given you a F2,3,or 4 error code, had it failed. I can't help but think you may have a faulty relay board or ERC/Control, If they do not communicate with each other, the oven will shut down. Y04100262 WPY04100260 Good Luck and Thanks Read More...
Frank November 09, 2011 for Model Number MER6872BCS The reason I was testing the sensors was I was getting a F12 on the top oven then a F32 on the botom ovens. When the codes appeared, the ovens shut off. When I unplugged the stove the ovens worked okay for several hours then coded again. Then I put a meter on both the ovens when they reached a temp of 350 and the top oven sensor read 1827 and the bottom oven read 1625 ohms (done the ovens seperately 10 minutes apart). Should I replace both the bottom and top sensors or replace the control/clock module. seems too coincidental that both sensors would go at once??
1 Answer Hi Frank. Use a ohm meter to unplug the oven sensor and test them cold. They will read 1,100 ohms cold. Rotate the wires as you test hem to insure no opens or shorts. Senors are part # 12001656. Check the power supply and make sure you are getting 240 vac , 120 vac respectively to neutral. This will effect performance. Make sure the elements ohm out (28-38 ohms) and are not open or shorted. Are the connections at the elements tight? Lower Bake elmt. part # WP7406P428-60. Lower Broil elmt. part # WP7406P218-60. Is the clock relays giving 120 vac out put at command given? Clock control is part # WP5701M406-60. Lower sensor is part # WP7430P044-60. F1-2 code is lower oven sensor , wiring or bad control. F 3- 2 is lower oven sensor. Thank You. Read More...
Kevin November 06, 2011 for Model Number Magic Chef 6892XVS I get an F2 Code when using the oven and the oven overheats. I have replaced both the sensor probe and relay board with new Whirlpool parts for this oven. I have tested the sensor probe at 350degrees and I get a reading of 1790ohms. The oven is still overheating. What am I doing wrong? Is there anything else I should check. The door lock seems to operate properly. The oven will not heat if the door lock is engaged. Only the self clean turns on when the door lock is engaged. I do not use the self clean feature. Thanks - Kevin
1 Answer Kevin, Based on your information, you may want to re calibrate your control, you're basically 50 degrees high. here's some information"To adjust the thermostat: 1. Press the OVEN TEMP pad. 2. Press the up pad until 550° is displayed. 3. Press and hold the oven temp pad for several seconds. The display will show the ambient oven temperature for a few seconds then 00 dgrs. will appear in the display. If 00° does not appear in the display, press the cancel pad and begin again. • If the oven temperature was previously adjusted, thechange will be displayed. For example, if the temperature was reduced by 15°, -15 ° will be displayed. Press the up or down pad to select the temperature change desired. • The oven temperature can be increased up to 35° or reduced by as much as 35° (-35 °) in 5° increments.• If you delay in selecting a temperature, the program will automatically cancel and 00° will disappear. Begin again if the Program cancels. 5. Press the CANCEL pad and the time of day will reappear in the display. The oven will now bake at the adjustedtemperature." Otherwise, you'll need to replace the ERC 12001607 Thanks and Good Luck Read More...
Frank November 06, 2011 for Model Number MER6872BCS I have put a meter on both the ovens at 350 and the top oven sensor reads 1827 and the bottom oven reads 1625 ohms. Is there anything else I should check before I order the control/clock module?
1 Answer Frank, Both sensors are the same and should have a resistance of 1650 Os at 350 dgrs. You didn't mention an issue, but if you're testing the oven temperature or sensor resistance, you need to pre heat the oven 15 to 20 minutes, then allow the oven to cycle off and on 3 times to get an average cycle time and oven temperature, and you should do the test on each oven separately. After you test the operation and temperature and resistance, you can recalibrate the control if needed. Thanks and Good Luck Read More...
Ashley October 27, 2011 for Model Number WW30430P Wife using Oven in bake mode at 350 degrees. She said it started beeping and F5 came on display, then F2 came up and stayed on. I turned off breaker and let it cool overnight. Turned on breaker this morning and oven display appears to be working properly. I set the bake temp at 350 and it heated up and maintained 350, then did 400 and it worked ok at that temp. What is your recommendation or opinion?
1 Answer Hello Ashley. Based on the fault codes you provided, it sounds like the oven temperature sensor 12001656 may be going bad and will need to be replaced. Hope this helps. Read More...
Joe October 25, 2011 for Model Number JDS9860BDS Hello, You suggested I measure the temp sensor resistance while the oven is 350 degrees. How do I do this? Turn oven on to 350 and then unplug and measure the resistance at the probe connector? Seems like it might be kinda hot? Sorry...But I must be missing something. I do appreciate the help. Thanks very much, Joe
1 Answer Hello Joe. Pull out the unit and remove the back off of it. Then turn the power back on and start the oven heating. When it reached 350, cancel the oven and unplug the unit. Then you can unplug the sensor 12001656 and test it, without touching the hot metal parts. Hope this helps. Read More...