Ian June 06, 2011 for Model Number MAYTAG MER5550AAW Can the Oven temperature sensor be cleaned without removing?
1 Answer Hello Ian. You do not need to remove the oven sensor to clean the oven. Hope this helps. Read More...
Rod T. June 02, 2011 for Model Number MGR5754QDW I have replaced the igniter already, but still won't heat my oven.
Vincent E. May 30, 2011 for Model Number gr556lrk0 - ser number lmm4597053 I have a whirlpool range (hot and cold) and the oven always cuts off when setting the oven pre-heating. If it is the temp sensor how do I get it out?
1 Answer Hello Vincent. To remove the temperature sensor, you will need to remove the screws inside the oven holding it in place. Then pull the sensor out and replace it with the new sensor. All of this can be done inside the oven. Hope this helps. Read More...
Chuck May 29, 2011 for Model Number JJW9530AAB I have an F2 Error code and a fan that continues to run on my Jenn-Air Oven. How can you determine if it is the RTD or the Relay Board that is faulty? Thank you!
1 Answer Hello Chuck! An F2 error indicates the oven temp is too hot. The relay board 74006613 or the oven temp sensor WP71001870 will need to be replaced. You can test these parts using a multimeter MA-DM1. Here is a link from our free repair forum you can refer to for help with using a multi meter. Hope this helps, thaks! http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Mitzi May 15, 2011 for Model Number svd48600B My jen-air oven won't heat up and the temperture display stays on 100, I replaced the clock assembly. What should I try next?
1 Answer Hello Mitzi. You will need to test the bake element WP71001680 and see if it is good. It should read closed for continuity. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Andrew May 15, 2011 for Model Number Maytag Gemni MER6755AAS My on indicator light stays on after we turn everything off. What could be causing this, do I have to replace a sensor?
1 Answer Hello Andrew. It could be a bad burner. You will need to test each burner, with the cook top cold, and see which one is bad. 1B to 2B should be open. If one is closed, you will need to replace that burner. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Wayne May 08, 2011 for Model Number CRE9600CCE My stove top works fine, But when I turn on the oven either bake or broil, I set the temerarture at around 350%.. Then immeaditly it drops down to 75%. And then in 30 sconds it shuts off, and then I get an F-5 error reading. Wayne
1 Answer Hello Wayne. According to the code you provided, you have a bad clock assembly 12001603. F-5 is for a Watchdog and hardware conflict, and the manufacture recommends replacing the clock assembly. Hope this helps. Read More...
Ingrid April 20, 2011 for Model Number Jenn Air w30400p I used the oven for dinner, and turned oven off, but the fan kept running. It ran all night. Do you think it is the sensor? The oven was cool to touch.
1 Answer Hello Ingrid. You can test the sensor and see if it is bad. It should read around 1100 ohms at room temperature. If it is reading around 1800 ohms, then the sensor is bad. If it is at 1100 ohms, then you may have a bad control board assembly WP71001799. You can test this with a multi-meter MA-DM1. Here is a link on how to use a multi-meter. Hope this helps. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Karl April 19, 2011 for Model Number w30400p I can get the sensor off the oven wall. How does the plastic connector come apart?
1 Answer Hello Karl. It has a clip that you press to release the connector. Hope this helps. Read More...
Tim April 18, 2011 for Model Number MER5770AAQ The temperature inside the oven doesn't match with what shows on the top display. We put a thermometer inside the oven and found that it fluctuates by up to 50 degrees - usually lower, but sometimes higher. Will replacing this sensor fix this problem?
1 Answer Hello Tim. You can test the sensor and see if it is bad. It should read around 1100 ohms at room temperature, and around 1600 ohms at 350°. If it ohms bad, then a new sensor should fix your problem. Hope this helps. Read More...