Bruce April 16, 2011 for Model Number CRE775 My stove top works fine but when I turn on the oven either bake or broil it starts but shuts off within 15 seconds, what is wrong?
1 Answer Hi Bruce. It could be the sensor if the temp goes blank and reverts to the achieved temperature. You will have to provide your serial number to locate the correct sensor. Thanks! Read More...
Carol April 14, 2011 for Model Number MER6770AAQ I am getting the F-1 error message on my range. I gather from what I've read this is the oven temperature sensor. How expensive is this to replace if I need to call a repairman?
1 Answer Hello Carol. If you can not access the screws for the sensor from inside the oven, then it will need to be uninstalled and the back cover removed to change the sensor. They are not hard to change, but can be difficult to get to, if you have to uninstall the oven. Hope this helps. Read More...
Mike L. April 09, 2011 for Model Number Maytag CWE900 In attempting to replace the upper broiler element, I found that the wire connection on one side had melted off. The wire on that side remains intact and looks OK, but the connector on the end of it is burned mostly off. Can I put a new wire clip on it and reinstall, or does the meltoff indicate that I need professional help?
1 Answer Mike, At this point , you can replace the wire terminal, just make sure it is rated as, a high temperature, 240 Volt,30 amp. wire terminal, (not the light weight "brass colored ones) and that you get a very good attachment(crimp) when you secure the terminal to the wire, and yopu'll be fine, as long as theres no other damage to the other comonents, sounds like you'll be fine at this point. Good Luck and Thanks Read More...
Bonnie March 31, 2011 for Model Number mer5765rcw I believe the sensor is 'cooked' as it were, I found some instructions that say I should be able to remove it from within the oven, the end bit won't go through the little hole. Can I remove the back to access this connection? Thanks
1 Answer Hello Bonnie. Yes, you can remove the back cover to access the connection. Hope this helps. Read More...
Max March 25, 2011 for Model Number B-59F-5TXW The oven temperature is at least 75 degrees lower than what is is set for. Could it be the oven temperature sensor or could it be a fuse?
Paul March 25, 2011 for Model Number 38HK-6TXW Thanks for the quick response on the temp sensor. Forgot to ask about inner glass on door [same oven]. Can't seem to find one, seems to be discontinued. Any ideas?
1 Answer You're welcome Paul! Unfortunately, that is correct, the outer door glass for this model has been discontinued. At this time, the manufacturer does not have a replacement part number and there are no cross references available. Sorry! Read More...
Paul March 25, 2011 for Model Number 38HK-6TXW I have an F3 code coming up when I try to preheat oven. Will sensor replacement solve this? Why are there 2 listings for part #33? Other sites indicate that you must know the Series 59 or 01, is this the difference? My oven does not appear to have Series 59 or 01 shown the only thing close is in the Serial #23C017499858. The "01" in the Serial number is the closest I can tell. No other info on Series is shown on nameplate. Which Part #33 should I order?
1 Answer Hello Paul! You're right on track! An F3 failure code indicates a shorted or open temp sensor. You will need to check the sensor harness and harness connection between the sensor and oven control. Replace the temp sensor if the wiring is ok. Both of the original temp sensors have been redesigned they are now the same part number. You will need to order 12001656. Thanks! Read More...
Jeff March 19, 2011 for Model Number ?? I have a maytag ceran glass top stove...Can't find model #..the stove gives a f-3 and f-7 error...please help
1 Answer Hello Jeff. The f3 code means Shorted or open oven temperature sensor (RTD)Check sensor harness and harness connection between oven sensor and oven control. Replace oven temperature sensor (RTD) if wiring is ok.The F7 code means Function key shorted or stuck. Replace touch pad or if touch pad is part of the clock, replace the clock (ERC). We would need to have your model number to provide you with the part information. Read More...
Ron March 14, 2011 for Model Number S176W Is there any way of replacing this sensor without removing the unit from the wall? Is the oven liner removable without disassembling all of the elements, etc.?
1 Answer Hello Ron. If there are no screws on the inside of the oven that is holding it in, then you will need to uninstall the oven. If there are screws on the inside, the wires should be long enough to change it without uninstalling the oven. Hope this helps. Read More...
Vicki March 06, 2011 I'm hoping that this part# AP4009009, will fix the F1-1 error code that keeps my ovens from working along with an alarm that keeps going off. I have a Maytag Gemini Model# MER6770AAB. Is this all I will need to fix this problem? How hard is this to fix.
1 Answer Hello Vicki. The sensor should be all you will need to fix this problem. Thanks. Read More...