Joe October 23, 2011 for Model Number JDS9860BDS Hello, Follow-up question to my earlier one: (Oven temp suddenly goes out of sight and burns food.) I removed and measured the temp sensor at about 65 degrees it reads 1055 ohms. Do I need a sensor or control panel or ??. Also will need to confirm your part number...Thanks much...Joe
1 Answer Hello Joe. You will need to measure the sensor when heat is applied. Turn the oven to 350°, and see if the sensor reads around 1650 ohms when the temperature is reached. If not, you will need to replace the sensor. Hope this helps. Read More...
Joe October 23, 2011 for Model Number JDS9860BDS Hello, Our oven suddenly will overheat and start to burn the food that's cooking nearly starting a fire. We have resolved this a couple times by turning off the breaker and resetting the oven. The problem always comes back. This is a real fire hazard as we don't know when it's going to happen. Should I start by replacing the temp sensor? If so...What is the part number I need? (Note: I have no error code associated with the failure.) Thanks very much....Joe
1 Answer Joe, Even without an error code, you could have a defective oven temp. sensor 12001656 and is a good place to start. If that does not solve the issue, you will need to replace the ERC/Clock WP8507P232-60, you could have a weak or sticky relay on the control, causing the element to remain on. Good and Thanks Read More...
Fred Gargiulo October 21, 2011 for Model Number mer6870aaw I have a Maytag Gemini Oven. My wife is complaining that the lower oven temp is off (too low). Is there a way to adjust that or a part recommendation to be replaced? Oven Sensor Probe perhaps. Thanks - Fred
1 Answer Fred, If you had a sensor circuit issue , you should have an error code in the display. Here are the basic instructions for recalibrating the oven temperature control "Oven Temperature Adjust: Bake temperature can be adjusted by pressing Bake in either upper or lower oven, entering a temperature of 550ºF, then hold bake key for 3 to 5 seconds. Auto set is used to adjust the temperature either + / - 35ºF in 5º F increments" . Normally you would get an average oven temperature (takes 30 to 40 mins. and an accurate temperature probe or meter) then calibrate the control as needed. Thanks and Good Luck Read More...
Kevin October 18, 2011 for Model Number 6892XVS Magic Chef I got an F2 code while using the oven. I checked the oven temp sensor with a multimeter and it read 1083 ohms. I replaced the relay board assuming the sensor was OK and the board was faulty. The oven is still overheating with the new relay board installed. Could the oven sensor need replacing even if it read 1083 ohms? How close to 1100ohms should it read? Can you suggest anything else I should check. Thank you
1 Answer Hello Kevin. You will need to test the oven sensor 12001656 when the unit is preheating. At 350°, the sensor should read around 1650 ohms. If not, then the sensor is bad and will need to be replaced. Sensors can test good at room temperature, but break down when heat is applied to them. Hope this helps. Read More...
J.R. September 09, 2011 Is a long tipped sensor better than or preferable over a short one, or does it matter? Thank you!
1 Answer Hello JR! It would be preferred to replace the oven temperature sensor used directly for your appliance model. May we have your appliance model number to help verify which is the correct part needed for your product? Thanks. Read More...
Louie B. August 27, 2011 for Model Number Cea4d59tdv Our Crowley electric oven shuts off with in 30 seconds when pre- heating it for broiler or bake. The stove top works fine.
1 Answer Hi Louie. The oven sensor is part # 12001656. The clock control is part # 7601P154-60. I would consider replacing both parts since the sensor tells the clock to control the temperature. Thank you. Read More...
1 Answer Hello Paul. For the Gemini model the put the label on a little metal flag on the rear of the control panel on the left hand side. The little metal flag will swing up and back down, just like on your mailbox. Thanks! Read More...
Antonio B. July 14, 2011 for Model Number CRE8600CCE I have an F-2 ERROR CODE in my Maytag Electric Stove. The top coil become very hot. When I try to cancel they still remain on. To shut off the coil I need to unplug the stove from the main socket. How can fix this problem?
1 Answer Hi Antonio. F-2 code is associated with oven temperatures reaching temperatures above 650 degrees. Check your door lock, Ohm your oven sensor(1,100 ohms@75degrees). Double check your wiring harness. If all these are OK, Then replace the control board. The oven sensor will give an F-3 code. the control part # is 12001603. Thank you. Read More...
Dielle July 13, 2011 for Model Number 686am-tksvw Admiral gas oven/stove Stove works, broiler works, but when I turn the oven on, it smells like gas while it's warming up and although the extra gas burns off. The oven doesn't get all the way up to temperature. Does this mean the temp sensor needs to be replaced? The ceramic starter glows and I have cleaned the burner holes. Thank you for your help, Dielle
1 Answer Hello Dielle. Based on the information you provided, it sounds like the igniter 12400035 is weak and will need to be replaced. If it is weak, it will cause the problems your having. Hope this helps. Read More...
Jeff M. June 11, 2011 for Model Number MER6772BAB We have a Maytag Gemini Double Oven. It has a failure code of F1-1. We replaced the upper temp sensor and upper element, now it has a failure code of F1-2, but the bottom oven has never been used. The clock and touch pad is working fine. The website says the bottom temp sensor has gone out, is this possible?
1 Answer Hello Jeff! Yes, it is possible for the lower oven sensor to short out without the oven ever being used. You can test this by using the upper sensor in place of the lower sensor to see if the failure code eliminates. If it does, replace the sensor 12001656. If it does not, check the oven control WP5701M403-60. Thanks! Read More...