Doug G May 16, 2018 for Model Number WM2780B Oven has started flashing F1 code with a buzzer. will an oven sensor fix this issues?
1 Answer Doug, This issue would most likely be caused by a faulty oven sensor on the unit. Read More...
Carole April 18, 2018 I have a Maytag Precision TouchContro 700, Model MER5775QAS, Serial 16302888EN. I have a code S Ab or 5 AB. What is the problem and how can we reset it.
1 Answer Carole, That would be "SAB" that would indicate the control has been programmed into the Sabbath mode . " To cancel the 12-hour shut-off and run the oven continuously for 72 hours: 1. Set the oven to bake. 2. Press and hold the Clock pad for five seconds. • SAb will be displayed and flash for five seconds. SAb will then be displayed continuously until turned off or until the 72-hour time limit is reached. BAKE will also be displayed if a bake cycle is in use while the oven is in Sabbath Mode. All other functions EXCEPT BAKE (Timer, Keep Warm, Clean, etc.) are locked out during the Sabbath Mode. To cancel the Sabbath Mode: 1. Press the CLOCK pad for five seconds. OR 2. After 72 hours, the Sabbath Mode will end. SAb will flash for 5 seconds. • The time of day will return to the display." Thanks, Read More...
Laura April 09, 2018 for Model Number Thermador oven I am getting an error code of F3 on my Thermador oven and it feels like it is overheating. The broiler coil is on with the oven coil.
1 Answer Hello Laura. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Fredrick S. March 29, 2018 for Model Number AEW3530DDS My Amana wall oven heats up to the desired temperature then won’t stay at that temperature. Entry to adjust the temperature by using control pad adjustment. Does it need new sensor/ probe?
1 Answer Hello Fredrick, If the sensor 12001656 reads about 1100 ohms of resistance at about 70°F, the sensor will not be the issue. The control WP74008878 will be the issue. I'm sorry but this part WP74008878 has been discontinued by the manufacturer and no satisfactory substitutions have been provided. You could contact a company like Corecentric Solutions 1-866-737-2244/ corecentricsolutions.com and inquire if they support board WP74008878. Read More...
Jerry February 12, 2018 I have a jenn-aire model JDS986AAP and the oven element (both) do not get hot. The keypad all works and can set different temps and it acts like it's trying to heat but it just doesn't get hot. Is the temp sensor likely the culprit?
1 Answer Hello Jerry. You will need to check and see if there is 240 volts coming to the unit and make sure the thermostats are good on the unit. If so, then the relay board will need to be replaced on the unit. Thank you. Read More...
Mark T January 25, 2018 for Model Number CWE5800ACB Okay, I pulled the OLD temperature probe from the back of my wall oven and the leads of the sensor were both tied into one single wire with a ceramic wire nut. I snipped the end of one of the jumpers, plugged it into the NEW probe and used the same ceramic wire nut to tie all three wires back together (yes I know this seems wrong but that's how the original was tied in) re-installed it and now I get the F3 error code.......any suggestions ?
1 Answer Mark, You will want to look for a second white wire that goes to the control board for the oven sensor. Check coming off the board for 2 white wires and follow them to the sensor. There should have never been just one wire. Read More...
Roland B January 01, 2018 for Model Number CRE9600BCL When I push any button nothing works, my burners all work. Do you think it is the control panel?
1 Answer Roland, Make sure that the control is not locked and if it is not and the touchpads are not working then this will be a faulty control board. Read More...
Will December 15, 2017 for Model Number KEDC205YWH0 I also have an F3 code. Which is the correct part number for the temperature sensor? AP12001656 or 8053344? Thanks in advance.
Mike November 19, 2017 for Model Number CWE4800ACB When wall oven turned off, I get an F-1 error code every few minutes until cooled down. any suggestions ?
1 Answer Hello Mike. Test the oven sensor and make sure it is good. If so, then the control board will need to be replaced in the unit. Thank you. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Janel S November 02, 2017 for Model Number ARG7600CC My Amana oven occasionally shuts off on its own or has F3 or F4 error codes. In my research it appears to be the oven temperature sensor. I have located this in the oven. I am interested in replacing this myself. Wondering about an accurate part number. The ones I am finding online don't look the same (flattened tip of sensor or much longer). Would you be able to help with this?
1 Answer Janel, The part number for the oven temp sensor on this unit will be WPY0314907. Read More...