1 Answer Hello Clark. Most Frequent Causes for F7 - A button on the touchpad is either stuck or short-circuited. You will need to replace the control board WPW10201915. Thanks. Read More...
Flo October 09, 2017 for Model Number Unable to find I have a cabinet oven and the temperature senor is not working. How do you install that sensor?
1 Answer Hello Flo. We will need your model number to help you with this. Please call 1-877-477-7278 or post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Alan September 02, 2017 for Model Number ALE643RBW The wire coming out of the heating element has burned in two for the third time now. A service tech repaired it the first time. It worked for two loads of clothes and burned in two again. The coating on the wire and the wire melts right at the connection. I replaced the connection the next time and hooked it back up and the same thing happened after one or two loads. It always happens on the side of the element opposite the thermal fuse and the Hi limit thermostat safety sensors. Is this due to a faulty heating element or something else?
1 Answer Hello Alan, This is normally associated with an air flow issue. You should first check the exhaust ducting for crimps and clogs. Any flexible ducting you locate should be replaced with rigid aluminum ducting for a full 4-inch diameter. This normally corrects the issue when the wire is properly spliced. Read More...
Marlene August 15, 2017 for Model Number AGR5715QDQ the burners work the broiler works but the oven will not heat? IT goes to bake and the temperature I put to 350 and it flashes bake and then goes to 100 degrees and thenno heat. IT worked fine and then next day I turned it on will not heat. ? HOW TO FIX?
1 Answer Hello Marlene, you'll want to make sure your igniter WP7432P136-60 is glowing a bright white. If you notice that it's not glowing a bright white or not coming on at all make sure you're getting voltage to it. If it's getting voltage you'll need to replace the igniter, if not you'll have to check the wires and test at the board to make sure voltage is being sent out. Hope this helps! Read More...
Marie April 11, 2017 for Model Number GS563LXSB0 I am having problems with my Whirlpool gas oven staying heated. The broiler works and will stay heated but when I bake, I can hear it ignite and start to heat up but then will stop and not stay heated.
1 Answer Marie, The most likely cause for this issue would be a faulty gas valve that when it gets heated up it closes off due to bad solenoids. This would require the valve to be replaced. The part number for the valve is WPW10293048. Read More...
Gary March 18, 2017 for Model Number JJW9627CAS The bottom oven will not heat, but the broiler works. I replace the baking element on the bottom and still no luck, is it the heat sensor that needs to be replaced? Does the heat sensor also control the broiler element?
1 Answer Gary, The oven sensor would not cause the bake element to work and you would need to replace the lower relay board which would be part number 12001914 but unfortunately has been discontinued by the manufacturer with no suitable replacement available. Read More...
Floyd December 29, 2016 for Model Number 709.78763406 I have a gas range and am having problems with the oven heating evenly. It states on your web page that it is probably due to the oven temperature sensor being bad, however, I can not find a sensor for my model but there is a temperature probe. Is this same thing as a sensor?
1 Answer Hello Floyd, The temperature sensor and the temperature probe are the same thing. I'm sorry but we will need to ask you to post a new question including the verified model number from your units' I.D. tag so we can recommend parts that can be guaranteed to work properly on your unit. Unfortunately, the model number provided is not coming up as valid. Thank you for your patience and understanding in this matter. Read More...
Floyd December 29, 2016 for Model Number 790.78763406 I have a Kenmore gas range model 790.78763406 and need to order an oven temperature sensor but can's seem to find the correct part number
1 Answer Floyd, The Oven Temperature Sensor, for the model number you supplied is 316490001 / 316217001. The part is in stock and available at this time. Thanks, Read More...
Will November 07, 2016 for Model Number 911 I have a Kenmore double wall oven (electric) that the temp sensors have both gone bad. 911 seems to be the only model number, followed by41369690. I can't find the right sensors. Can you help?
1 Answer Will, The part number for the oven sensor for your unit will be WB21X5301 which you will need one for each of the ovens if both are bad. Read More...