Kim November 14, 2014 for Model Number RF315PXKQ0 Hi on the oven the code f3e5 oven temp sensor so replaced it. the oven still won't work and the same code comes up. Does the wiring harness need to also be replaced?
1 Answer Kim, There isn't an F3E5 error code for your range,(probably a typo). Occasionally a sensor wire harness is needed, but very seldom. Try this, disconnect the oven sensor harness from the ERC/Clock. With a meter, check each wire in the connector to the chassis, there should be no resistance reading. If there is then the wire is chafed or shorted to ground, and will need to be repaired or replaced. Then place the meter leads between the openings in the connector, you should have a resistance reading of 1050 to 1100 ohms. This will verify that the sensor and the wire harness are in tact and operational. If the readings are correct, you will need to replace the ERC/Clock WP6610463. Read More...
Tim October 29, 2014 for Model Number wfe371lvso Yes I bought a control board and my stove does not heat up good broiler works great do I need oven tempature sensor.
1 Answer Hello Tim. If the broil works, but the bake does not, you will need to check the bake element in the unit. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Ralphie October 26, 2014 for Model Number MER6775AAQ the bottom oven doesn't heat. replaced the element; no help. The schematic shows a heating sensor. Is there one of these for both ovens or does one control both. If this is defective could this be the cause of non heating?
1 Answer Hello Ralphie. There is one in both ovens. However, on this issue, you need to check the control board. If it is not sending power to the element, then the board is bad. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Xing M. October 23, 2014 for Model Number WFG361LVB0 The oven stopped working last Friday. The stove tops work well, and the clock is fine and no error code displayed. When I set a temperatue, the ignitor will light and off immediately. Do you think that was the temperature sensor problem or otherwise?
Ray July 23, 2014 for Model Number F367LEKQ 1 The gas oven does not hold its temperature. It does not heat all the way to what you set it on. I am getting no codes on the display. It comes on and lights the gas and will relight every time you change the temperature setting. Is it a temperature sensor?
1 Answer Ray, The temp. sensor is a good place to start, it could become erratic with age, debris or after a self clean cycle. Since you seem to be sure the gas burner ignites properly for an extended period. we won't consider the gas valve or igniter as the issue at this point. Read More...
Jeff May 28, 2014 for Model Number Admiral 687WK-TKSAW Food is taking longer to cook in oven. Have had to adjust temp up 75 deg. in the past. Now it is up to 125 deg. IE - want 375 deg so have to set oven for 500 deg. Do I need to replace the oven sensor kit or what? We got the gas oven in 1992 and have been very happy with it!
1 Answer Hello Jeff. You may have a weak igniter. Test for 3.2-3.6 volts AC at the gas safety valve with the igniter turned on. If the voltage is there, you have a bad safety valve. If the voltage is low, you have a weak igniter and the igniter will need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Daryl May 22, 2014 for Model Number cwe5800acb I have tried posting on the forum but have received no reply, we bought the control board and sensor from you to repair our top oven on the cwe5800acb, but still not working. Need to figure out what next.
1 Answer Hello Daryl. Make sure the element is good. If so, check the limit switch 7403P063-60 and see if it needs to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Cari C April 04, 2014 for Model Number MER6875BAS I moved to a new home with a Maytag Gemini Electric Smoothtop Double Oven Range model: MER6875BAS When I set it to bake, the oven preheats, but when it beeps to tell me the temperature has even reached, it is low by 75-100 degrees. This occurs in both ovens. I had a local repair company come to my home and they said there are only two parts that can be replaced on this range--the motherboard or the elements. I see here that there are a lot more parts than that. What should I try first?
1 Answer Cari, The first thing that you will want to check is the oven sensors. The oven sensor would need to be checked for resistance, the resistance at room temp should be 1090 ohms. If the sensor is not showing the proper resistance then you would need to replace them. Also check the wiring from the control to the sensor to make sure that there is no damage to the wiring. If the sensor and wiring checks ok then the Control would be the issue. Read More...
Doug April 03, 2014 for Model Number MES5552BAW I asked a question over the weekend about my Maytag model #MES5552BAW range. The fan constantly runs and the oven doesn't heat at all. When you try to preheat the oven the temperature on the screen immediately raises to the desired temperature, but doesn't heat up at all. Your answer was to change the control board, and that did not solve the problem. Any other ideas?
1 Answer Hello Doug. You can test the oven sensor. It should read around 1100 ohms at room temp and 1650 ohms at 350°. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Kris March 30, 2014 for Model Number kenmore 75322003 Our oven temp drops during the banking time. I turn the temp off and set the temp again, and in a few minutes it will beep that it is the right temp again. What part do we need to replace. Thanks for your help
1 Answer Hello Kris. Based on the information you provided, it sounds like the control board is bad and will need to be replaced. Read More...