Chris September 03, 2015 for Model Number JJW9627CAB I lost the display on my Jenn Air double oven a while ago. Then the oven started not shutting down the element when it reached temp. I replaced the Oven control board but it still won't shut down the element. It does ding when it reaches temp. What next? Thermostat? Oven Temp Sensor Kit? Thanks
1 Answer Hello Chris. It sounds like the relay board 74006613 is bad and will need to be replaced on the unit. Read More...
Ron M August 08, 2015 for Model Number mer6555aaq My lower oven element doesn't heat, I have tested element with OHM meter and it reads 21 ohms which indicates it is OK. When I put it on bake after a while I can here some clicking about every 3 - 5 minutes. What is causing it not to heat? I don't have a wiring diagram to see if there is some type of relay or fuse not sending a signal. Thanks Ron
1 Answer Ron, There is not a thermal fuse or relay that would be in line for the bake element. The issue with the unit will be caused by a faulty relay on the electronic control board which is part number W10769079. Read More...
Todd June 02, 2015 for Model Number AER5715QAQ My Amana AER5715QAQ is preheating much more slowly than usual - although it seems to occur somewhat sporadically. Once it is preheated, it seems to keep the heat at a consistent level and cooks properly. What might be causing the slower preheating and what can I do to try and address it? Thank you!
1 Answer Todd, You will want to test the oven sensor to make sure that the sensor test out at 1090 ohms at room temp of 77 degrees. The other thing would be a weak element could cause the unit to not preheat properly. Read More...
Bill April 20, 2015 for Model Number MEW5530DDB The maytag wall oven has the following symptoms. 1. None of the front touch buttons work unless you press the any of the number buttons (randomly). Then all the butttons work. 2. Press bake, broil etc and set temp and bake or broil again. oven starts. a short time later before the temp rises, the oven has two short beeps, a couple of seconds, and two more short beeps. The oven the turns itself off about 30 seconds later.
Ed March 31, 2015 for Model Number 66675775890 Top works and broiler seems to work. When tuned to oven, the igniter comes on, but it does not light. suggestions?
1 Answer Hello Ed. Test for 3.0-3.6 volts AC at the gas safety valve with the igniter turned on. If the voltage is there, you have a bad safety valve. If the voltage is low, you have a weak igniter and the igniter will need to be replaced. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Don January 25, 2015 for Model Number CHG9800BAM Oven sometimes takes 20 or 30 minutes to reach temperature target, sometimes only 10 minutes, which used to be its normal time. Once at the target, it's not reliable: it may cook hotter or more likely cooler, based on a portable oven thermometer. Food often comes out underdone.
1 Answer Don, You will want to check the oven sensor to make sure that the resistance of the sensor is 1090 ohms at room temp. If the sensor does not check ok then it would need to be replaced. If the sensor checks ok then the control board would be the issue. Read More...
Tim December 27, 2014 for Model Number JES9800AAS My stove heats to the desired temperature, then drops. If I cancel and reset to the desired temperature, it reheats to the desired temperature, then drops again. Do I need a temperature sensor?
1 Answer Tim, The oven temperature sensor 12001656 is a good and logical place to start. There are other possibilities, but the sensor is the most likely issue based on your post. Read More...
Jim December 08, 2014 for Model Number gy399lxub1 I'm working on an oven model gy399lxub1. The oven is running about 20° hotter than the read out on the panel. There is no error code, I suspect the temperature sensor. Is the temperature control on this system self calibrating?
1 Answer Hello Jim, While the temperature sensor could be out of tolerance, (should read about 1100 ohms at about 70°F), the control is also manually settable by 35° above and below default. This is accomplished by the following: 1. Press BAKE. 2. Enter 550° by pressing the appropriate number pads. 3. Immediately press and hold BAKE pad for several seconds or until “0°” appears in the display. If the oven temperature was previously adjusted, the change will be displayed. For example, if the oven temperature was reduced by 15 degrees the display will show “-15°.” This information is assuming the model number is YGY399LXUB10 since the model number you posted did not come up as a valid model number. Read More...
Mechanicalguy November 29, 2014 for Model Number WW30430B Access to temperature sensor on bottom oven of jenn-air electric oven WW30430B. To remove the oven[s] is a major job due to the way the oven unit was installed. Some years ago we replaced the clock board and sensor of the upper oven. We enlarged the sensor hole and managed to pull the connector wire and plug out far enough to replace the sensor. We were able to easily replace the top sensor again. but the bottom sensor appears to be hung up behind the back of the oven. I'll try enlarging the bottom sensor hole, but anyone have a better idea? Thanks, Dave
1 Answer Mechanicalguy, Aside from pulling the unit out to access the connector for the oven sensor, this would be the only way to get it by going from the front and getting the connector through the hole. Read More...
Paula November 16, 2014 for Model Number CHE9830BCE F-7 code keeps coming on, press cancel to stop, but comes right back on. Had to unplug stove to stop. Is this the oven sensor? Have been having problems with the panel not staying light up.
1 Answer Paula, The issue with your unit would be caused by a stuck key on the control pad. This would require the clock to be replaced which unfortunately has been discontinued by the manufacturer. The part number is 12001611. Read More...