Don K March 27, 2014 for Model Number 790.78823407 I have a Kenmore Gas Range, Model # 790.78823407. The Broiler has two settings, LOW and HIGH. We use LOW, often for broiling. The LOW setting has no INITIAL glow and the BACK of the upper Ignitor (the part where the flames show) and the flames do not appear. However, on HIGH, all operates normally. If I have the broiler on HIGH and switch to LOW, the flames go out. Is there a way to confirm what part I need? Thank you
1 Answer Don, You will want to check your oven sensor 316490001 at room temperature and it should be approximately 1090 ohms. If it checks ok then the issue will be caused by a bad oven control board 316418501. Read More...
Francine March 18, 2014 for Model Number MER5750AAW My oven gives an F3 code. Is ordering the Oven Temperature Sensor Kit the right item for this?
1 Answer Hello Francine, You are correct. The F3 fault code is the indication of a failed sensor 12001656, sensor connection, or, in a worst case scenario, a failed control. Read More...
Gary March 11, 2014 for Model Number cwe5800ace Top oven will not heat at all, on bake or broil. set temp at 350 to bake and it goes back to 75. set to broil H1 and nothing happens. Just a little while back replaced the bake element. Could this be the sensor or something else?
1 Answer Hello Gary. Based on the information you provided, it sounds like the control board 7601M285-60 is bad and will need to be replaced on the unit. Read More...
Steve February 24, 2014 for Model Number Magic Chef Electric Range 68HN-4TVW This just started overnight - I turn the oven on to any temp, and after about 30-45 seconds, it shuts off. Same for the broiler. Stove top, clock, timers, fans - everything else is fine. I have unplugged for a long time to "reset", but that did not work. I have also taken out the oven temp sensor and cleaned it off and put it back in (just swinging for the fences to get it to work) - and that did not work. I have looked at all of the wires that I can see, and I don't see any that are damaged. Thanks in advance for any info!
1 Answer Hello Steve. Based on the information you provided, it sounds like the control is bad and will need to be replaced on the unit. Read More...
Steve February 04, 2014 When oven is turned on the temperature goes to 500 degrees and stays there. Is this caused by the sensor or thermostat or board problem?
1 Answer Hello Steve. You need to test the oven sensor. It should read around 1080 ohms at room temp. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.htmlIf good, replace the board in the unit. Read More...
Michele January 20, 2014 for Model Number MER6770AAW, serial # 12637572WS Hi, We get a F1 code when trying to use either oven, about a month ago it did this when I was using top oven, now they are both giving a problem. Yesterday I didn't even have oven on yet, was just using the top and it did this. Any thoughts?
1 Answer Michele, You will want to check the oven sensors as the f1 error is for runaway temperature. The resistance of the sensors should be 1090 ohms. If not within range then replace. If they both check ok then the control board would be the issue. Read More...
Denise January 13, 2014 for Model Number Jenn Air Oven model WW27110 On heating my oven, it began beeping and a flashing F2 appeared. I tried turning the oven off, but it would stop beeping for a few seconds and then start again. The only way to stop the beeping was to turn it off from the mains. When I opened my oven I noticed that it was far hotter than the 350 setting. Is this a problem with the oven sensor? What part number should I purchase?
1 Answer Hello Denis. If the sensor ohms around 1100 ohms at room temp, replace the control board. If the sensor does not ohm properly, replace the sensor. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Margaret January 13, 2014 for Model Number CER3760BGW I have an f1 error showing. My oven will not work. Error appeared after a self clean cycle. I have disconnected the sensor & the error disappeared, but obviously the oven does not work, help!!!!
1 Answer Hello Margaret. Test the sensor. Should read 1100 ohms at room temp. If bad, replace the sensor. If good, replace the control board. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Jennifer January 02, 2014 for Model Number CHE9800BCE We ordered a sensor, 12001656, as oven kept having F3 error. We got it installed but it still is doing F3 error. Any suggestions on what we need to do. Thanks.
1 Answer Hello Jennifer. If the sensor and wiring is good, you may have a bad control board 12001607 in the unit. The board has been permanently discontinued by the manufacturer and we don't know of any source or replacement for the part. Read More...
Patty January 02, 2014 for Model Number 790.75761001 Trying to locate oven temperature control sensor, it is not like on the video.