Robert December 01, 2025 for Model Number JDS9860AAP My temp probe is reading 88 ohms at 71 F deg. Is this reading within an acceptable range?
Andrew December 19, 2023 for Model Number seahonk1@yahoo.com my whirlpool gas over would not light so i replaced the gas safety valve but now it will not heat up paste 250 degrees? and takes some time before its lights up.
1 Answer Andrew, We will need the model/serial numbers to properly research your issue and give you the correct information and part numbers for the machine you are working on. Read More...
Bob November 09, 2023 for Model Number JDS9860AAP Oven and broiler are not getting up to temp. There are no error codes in the control display. I am thinking that the temperature sensor may have failed. I would like to try to test the sensor with an ohmmeter. What resistance should I see at room temperature? Thank you, Bob
1 Answer Bob, Temperature F (C) Resistance (Ohms) 100 (38) 1143 200 (94) 1350 300 (149) 1553 350 (177) 1654 400 (204) 1753 500 (260) 1949 600 (316) 2142 700 (371) 2331 800 (427) 2516 900 (483) 2697 1000 (538) 2874 Read More...
Mike March 17, 2023 for Model Number GGE350LWS00 I have a double oven and both ovens the temperature seems to fluctuate. Could this be a control board issue? If so, do you stock this particular part? More information would be that when setting the temperature, say 350 it takes a long time to reach. Then it may hold for a short while then I can see that the heating element is staying on,and the temperature is rapidly rising. So, I'll reset the temperature to a lower setting so that the element will shut off. Thanks in advance for your help.
1 Answer Mike, Thanks for the question!!! You can test the oven sensor at room temperature, it should measure around 1080 ohms. But let's talk about oven operation. An oven set to 350 achieves this as an average temperature. Meaning it heats up to 400 then shuts off cools down to 300 then turns back on. This allows the oven to maintain an average temperature of 350. Read More...
Ruffianfan January 26, 2023 for Model Number CRE8600ACL Maytag Range A few years ago the oven would shut off and generate a F3 or F4 error. I replaced the temperature sensor, got the error a few more times, then it was fine for a few years. Now, with the oven off, I am getting a random F2 error. I turned it off at the breaker, turned it back on a day later, did not even use the oven, and about a day later the F2 error returned. Will another temperature sensor fix this? Thank you.
1 Answer Rufffianfan, It would be recommended to test the oven sensor for a resistance of 1090 ohms at room temperature. If the resistance is good then this will be a control board issue. Read More...
Roy January 13, 2023 for Model Number SVE47600B Our oven appears to raise the temp to the desired level, but temp is not maintained and drops to a lower level. Based on what I have researched, I am thinking it might be the Oven Temp Sensor. Not getting any error codes. Are error codes stored, and it so how can I see any existing codes.
1 Answer Roy, It would be recommended to test the oven sensor for resistance of 1080 ohms at room temperature and 1654 at 350 degrees. If the sensor resistance is off then replace the sensor and if it is good then replace the control board. Read More...
Joe May 16, 2022 for Model Number WW30431 P1 I have a Jenn air model WW30431 P1. My top oven drops out after being on for 40 to 45 minutes regardless of the temperature settings. The oven shut off and it start to beep and it will not go on after that. Is it the temperature sensor acting up. I just replace the control board. Let me know. Thanks Joe
1 Answer Joe, Check to see if the cooling fan is running and if it is not then this will be the most likely cause for this issue. Read More...
Joe May 16, 2022 for Model Number WW30430P I have an F7 beeping fault, plus my top oven drops out after being one for 45 minutes or so. Is it the temperature sensor acting up? Thanks Joe
1 Answer Joe, Based on the information provided I would recommend testing the components suspected using the tech sheet provided with the machine. Read More...
Ben April 27, 2022 for Model Number WFG515S0JS0 My Whirlpool gas oven keeps heating and won't shut off, or at least, it's heating to about 500 degrees when set at 350.
1 Answer Ben, the oven sensor W10833885 would need to be tested for resistance to identify if it is operating properly. It should measure about 1100 Ohms at room temperature and it should raise 2 Ohms for every 1°F warmer it gets when heated with a hairdryer. If it tests good, the likely cause of failure would be the control W11393093. Read More...
Vernon October 01, 2021 for Model Number JER8855 Good day, when you set the oven to 350 degrees (or any temperature) the buzzer goes off to let you know its at the desired temp. But its not, its 25 - 30 degrees low. If you let it sit longer, than it does reach the desired temp. Do you think its the oven temperature sensor or the control board?
1 Answer Vernon, Thanks for the question!!! I don't think any parts need to be replaced. The typical oven thermometer that is widely used, is a slow reacting gauge. That is why after time it gets to temp. Before you change anything find a fast-reacting thermometer. In the field, most technicians use a multimeter with a thermal probe. This allows for real-time temperature readings. Read More...