Melissa October 06, 2015 for Model Number kenmore series 70 bought in 2008 The dryer stops but the buzzer continues buzzing until I open the door. If I don't open the door the timer continues to the next cycle I do still have heat.
1 Answer Hello Melissa, I'm sorry but we will need the model number from the units' I.D. tag so we can pull the wiring diagram. This could be the centrifugal switch in the motor, a bad timer, or a harness issue. Read More...
Brian July 26, 2015 for Model Number 500.015 I have an electric dryer, got a new push/start switch. It has 4 prongs. part number is 3395385. I need to know which is the ground and if the black wire is the ground wire. Tks
1 Answer Brian, To properly assist you we will need your model number to help you with this. Please post your model number with a new question on the parts page. http://www.appliancepartspros.com/modelnumber_locator.aspx Read More...
Kevin May 04, 2014 for Model Number kenmore dryer model #110.66732501 When dryer is done alarm stays on and when I open the door it stops. Then I shut the door the dryer starts up with out hitting the start button. Does this mean the starter switch is bad or is it the alarm switch?
1 Answer Hello Kevin. You can test the switch. If it does not read closed when not pressed, it is fine and the motor will need to be replaced. As for the alarm, you will need to order and replace the timer on the unit. Read More...
Luis March 13, 2014 for Model Number 110.67522600 I was checking the blower running when the back panel touched the dryer cycling thermostat and shorted it out. Now the Dryer won't start running.
1 Answer Hello Luis, The cycling thermostat is in the heating circuit and will have nothing to do with the unit running. When the short occurred, the breaker probably tripped in the circuit box. If this is not the case, you should check the dryer plug for burned spots and the terminal block for loose or burned contacts. The excessive current flow from the short could have accelerated the failure of a loose connection. Also check the door switch. Read More...
Rene December 22, 2013 for Model Number 110.72702100 Dryer won't turn off when I push to turn off. How do I troubleshoot this switch? The 4 tabs are throwing me off and make me believe that this May go to a relay. Thank you very much!
1 Answer Rene, The push to start switch would be checked by checking continuity when you push the switch. If the unit is not going into the off position when it is running then the most likely cause would be a faulty timer. Read More...
Importantcargo September 28, 2013 for Model Number 86581110 I have an old model Kenmore Dryer (electric) Model 86581110. The on/off push button won't start the dryer. When I push it in, the dryer makes a buzzing noise. That's it. The drum does not turn or heat up. What part do I need and is there a video that shows how to install it?
1 Answer Hello Importantcargo. It sounds like the motor is bad and will need to be replaced. Read More...
Alan L. April 30, 2013 Have an older Kenmore series 70 dryer. It will not start. I have checked the thermal fuse and there is full power to the unit. There is power at the on/off switch. I suspect the switch but want to be sure before ordering part. Door switch appears OK and I have tried starting the dryer in various cycle settings Thanks.
1 Answer Hello Alan. The start switch should read closed for continuity when pressed. If it does, then it is good. You can test this with a multi-meter TJMA-DMT3. Here is a link on how to use a multi-meter. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4810-how-check-continuity-ohmmeter.html Read More...
Chuck December 04, 2012 Press the dryer start button and dryer starts to turn, when you let go and it stops turning, smells hot like something overheating.
1 Answer Hello Chuck. Based on the information you provided, the motor is bad and will need to be replaced on the unit. Read More...
Ron May 14, 2012 for Model Number 97374200 73742 The timer runs and never stops. The buzzer stays on when the cycle ends. I show continuity on the switch when it isn't actuated. Do you think this is a bad switch? I replaced the timer already as it wouldnt advance.
1 Answer Hello Ron, If the switch shows continuity without actuating it, it is bad and requires replacement. I couldn't look the part up for you as there is no valid model number posted. Read More...
Ron May 14, 2012 for Model Number 97374200 73742 start/buzzer switch- buzzer stays on when turned on, timer advance motor runs constantly through cycles...swith bad? have replaced timer already since it went bad recently
1 Answer Ron, Did you check and make sure you attached the buzzer wires to the correct timer terminals ? Yes check the start switch for a "momentary" closed circuit, when the button is pressed, or replace the switch. The alternative would be, a faulty motor circuit or white(N) wire to or from the motor and timer. Thanks and Good Luck Read More...