Stacey April 25, 2013 for Model Number MDB7600AWW Does the control panel include both the cover and the electronic components? Our panel got stuck flashing numbers from 50 down to 1 over and over and would not stop! We unplugged it and think we need to replace the control panel. Can you tell me if we are on the right track? Thanks!
1 Answer Stacey, The Control panel 6-917713 comes with the panel itself and the membrane switch/keypad. All other electronic components would be separate. Read More...
Nick October 08, 2012 for Model Number MDBTT79AWB Dishwasher will not start, the control panel flash when you first shut the door all lights light up. New door latch with switches.
1 Answer Hello Nick. If the door switches are new, you need to order and replace the control panel 6-917713 on the unit. Read More...
David September 11, 2012 for Model Number mdb8600AWS My control panel flashes "9" part of the time. Should I replace the control panel or just the control board? The dishwasher works fine otherwise.
1 Answer Hello David, This is a bad control panel 6-917713. The rinse cycle is 9 minutes long. When this occurs, the rinse button has collapsed and is making as though it were being pushed. You do not need the control board. Read More...
Evan September 05, 2012 for Model Number MDB7600AWQ In response to your recent reply re: "No. 9" flashing on the LED display. We took your advice, purchased a new display panel and just installed it last night. Now the numbers on the LED display are about half readable, although it does seem to cycle through the selected wash and/or rinse cycles. Thoughts?
1 Answer Hello Evan. You need to check and see if the ribbon cable is plugged into the control board good. If not, it will cause the issue you are having with the display on the control panel 6-917713. Read More...
Mark F. September 05, 2012 I need to replace the touch panel on my dishwasher. What kind of warranty comes with the part (touch panel)?
1 Answer Hello Mark! Please see the following link to our one year part warranty we offer. This will provide further information regarding the warranty we offer on all parts. Thanks! http://www.appliancepartspros.com/customerservice/warranty.aspx Read More...
Evan August 19, 2012 for Model Number MDB7600AWQ Our LED display will flash "9" and no wash cycle will work. When unplugged for 10 mins., then sometimes the cycles will work normally, but NEVER just the rinse cycle alone - assuming we just needed it. Also, the 3 remaining wash cycles, sometimes for ex., the Normal wash button or Auto-clean button will flash during their cycle. But sometimes, regardless of which wash cycle button is pushed, it goes right to the rinse cycle and shuts off. Other times, when using the Normal or Auto-clean, it will start out as "2H" and then w/in mins., goes to rinse cycle and then starts all over again. I replaced the circuit panel a yr. ago, plus this last Oct. put in a new water pump and impeller. Should we replace and buy new? If new, what Brand and model(S) would you recommend? Granted this is a 9 yr. old unit - we hate this throw-away society. We appreciate any help you can give us.
1 Answer Evan, You'll need to repalce the control panel/keypad assembly 6-917713. The rinse key is collapsing and selecting the rinse cycle, or the tracer ribbons have deteriorated. You're about halfway through the normal life expectancy of a MTG dishwasher, and with the repairs you've made previously, it may be worth one more. Thanks Read More...
Kal May 20, 2012 for Model Number MDB8600AWW Serial no: 14194739CA. All other buttons seem to work fine.. but not the Start/Cancel and the Normal Wash buttons. I had replaced the latch assemble a couple years back. I opened the pannel to see any loose connections.. but could not fine any. What do you think is wrong? Since this is the 2nd issue in the last couple years, would I be better off replacing the washer. Everything else seems to work fine as of now.
1 Answer Hello Kal. Based on the information you provided, it sounds like the control panel 6-917713 is bad and will need to be replaced. Read More...
John Omaha April 29, 2012 for Model Number MDB7600AWS The control panel works sometimes if the touch pad is pressed hard enough. Do I need to replace the Panel-Con? Thanks
1 Answer John, Yes, it's time for a new control panel/keypad assembly 6-917713. Your description is a classic sign of a keypad on the "way out". Thanks and Good Luck Read More...
George R. April 24, 2012 for Model Number mdb8600aws I was told I need the touch control panel for this dishwasher. Is part ap4365044 correct?
1 Answer Hello George! Yes, the control panel 6-917713 is correct for your model MDB8600AWS. Thanks! Read More...
David L February 26, 2012 for Model Number MDB 7600 AWQ Can you give me a step by step to remove and replace the control panel? My current panel is working fine but the plastic broke out around the door latch and left a gaping place where the latch snaps down when locked. I guess I have to replace the whole panel? If so I can order in bisque but would like to consider steps to replace. I have already once replaced the door latch so I am acquainted with the loosening of the back panel. What is involved in connecting the various controls of the panel electrically? Is is as simple as the door latch was? Guidance will be appreciated.
1 Answer David, Here you go. " Control Panel The Membrane/Facia on the Control Console is not replaceable. Removal 1. Disconnect power to the machine.2. Remove the Inner Door Panel. (See paragraph Inner Door Panel removal).3. Remove PC Board Housing Cover. 4. Disconnect Membrane Switch from PC Board. 5. Remove PC Board Base.6. Lift out Latch Assembly. 7. Remove 4 screws securing Control Panel to Outer Door. NOTE: Facia is susceptible to damage during reinstallation. Inner Door Panel Removal of the Inner Door Panel will allow access to the Microprocessor Board, Door Switches, Detergent / Rinse Aid Dispenser, and Vent Assembly. Removal 1. Disconnect power to the machine. 2. Open the Dishwasher door. 3. Remove the 11 Torx™ screws along the sides and top of the Inner Door Panel. 4. Separate the Inner Door Panel from the Outer Door. 5. Disconnect wires from the Vent and Dispenser Wax Motors before pulling the Inner Door Panel away from the Dishwasher. PC Board Removal 1. Disconnect power to the machine. 2. Remove the Inner Door Panel. (See paragraph Inner Door Panel removal).3. To access PC Board, remove 1/4" screw on PC Board Housing Cover. 4. To remove PC Board, loosen (2) 1/4" screws securing PC Board Base to Control Panel. 5. Remove pin and ribbon connectors from PC Board. 6. Depress tabs on PC Board Housing to remove PC Board." Thanks and Good Luck Read More...