Julie L December 11, 2013 for Model Number MDB6701aww3 What's difference between AP4365248 and AP4364448?
Fran November 04, 2013 for Model Number MDB6701AWB The dish washer control panel does not work properly or at times not at all. It only has functioned on regular wash since we had it for a few months. We bought it new in 2008.
1 Answer Hello Fran. Based on the information you provided, you will need to order and replace the control panel on the unit. Read More...
Carolyn October 22, 2013 for Model Number mdb6601aww I need to replace control panel in dishwasher. Is this a difficult process? I am very handy and mechanical
1 Answer Hello Carolyn. No, it is not hard to replace the control panel on the unit. You will need to disconnect the power to the unit. Then remove the screws securing the inner door panel. Remove the inner door panel and remove the cover off the control board. Remove the ribbon cable from the control board and remove the screws holding the control board housing in place. Next remove the screws holding the control panel in place. Reinstall with the new control panel in reverse order. Read More...
Tara September 24, 2013 for Model Number MDB6601AWS Non of the lights on my touchpad will work. I read some info online that it might be the control board so now was have forked out the $150 for a new control board and the dishwasher is still not working. We checked the breaker and that is not the issue either. Is it possibly the touchpad that needs to be replaced? If so what is that part and price?
Jeff August 14, 2013 for Model Number MDB6701AWW3 My Maytag dishwasher Start button does function anymore and the washer will not run. Is this the front panel or circuit board/wiring issue? Thanks!!
1 Answer Hello Jeff. Make sure the door switches are good. If so, and the button doe not work, you will need to replace the control panel on the unit. Read More...
Eldon August 02, 2013 for Model Number Maytag MDB6701AWS3 When I push start/cancel button it does not do anything. The other buttons light up what is the Problem
1 Answer Eldon, If all lights light up but the unit does not start then it will most likely be a bad control panel. Read More...
Leslie May 27, 2013 for Model Number MBD6701AWS3 Flashing code 8 on the board with the rinse cycle light lit. What do I need to fix? Other boards have said the mother board, but what parts do I need?
1 Answer Leslie, The control board that you would need for the unit is part number WPW10218837. Read More...
Dave April 28, 2013 for Model Number MDB6601AWQ My dishwasher stopped working. When you select a wash cycle and close door the minutes for selected cycle flashes and I press start but it will not work. A couple weeks ago we had a short power outage and the problem began. I unplugged everything from the control board and left it till next day, plugged all back in and it began working. Now same problem but tried all the same things but nothing is working, minutes just keep flashing but start button will not work. Any suggestions on what it could be?
1 Answer Dave, Based off the description it sounds like the keypad has a shorted start button not allowing contact to be made and you would need to replace the control panel 6-919822. Read More...
Scott February 08, 2013 for Model Number Amana ADB3500AWW Hi, we have the Amana ADB3500AWW dishwasher. It is stuck in Auto Wash Mode. Start/Cancel seems to be the only button that works. I'm wondering if this is typically a control board problem or a keypad problem? Also, two control boards that look about the same are listed for this model, which is the right one?
1 Answer Hello Scott, You would want to check to make sure that the key is not stuck. Disconnect power to unit for approximately 30 minutes to allow to reset. Upon reconnecting power if the unit continues to only have auto wash on then you would need to replace the membrane switch 6-919805. As far as the control boards go the reason for the different part numbers is due to series change. If the first 2 digits of the serial number are before 33 then you would use control board part number 12002709 If it has 33 or higher then part number WPW10218825 is the control board you would need. Read More...
Linda H. February 04, 2013 for Model Number MDB6601AWW Door latch on model mdb6601aww dishwasher broke. handle popped in and wont' pop out. We have ordered a new one. and will install it. Is there a step by step guideline for changing that door latch assembly?...without damaging the door. Thanks.
1 Answer Linda, the door latch is part number WPW10275768. You will need to disconnect the power to the unit. Remove the screws securing the inner door panel. Raise the door panel and gain access to the latch assembly. Unplug the wires from the latch and reinstall with the new latch in reverse order. Thanks! Read More...