Melissa April 06, 2017 for Model Number MDB6601AWW Hello, I seen where white was discontinued for this dishwasher (6-919824). The only option it gives is to replace with 6-919822 which is black. So, my question is I got part 6-919845 so it wouldn't be such a bad clash. Well that part doesn't have tough scrub button. I can live without tough scrub, just wanted to get someone else's opinion on if that would be ok to run like that. Already ran a load and all cycles work just wasn't sure if it would present a fire hazard or if it will just be a empty slot where the ribbon plugs in.
1 Answer Melissa, As long as there were no loose electrical wires left loose or hanging inside the door panel, then it should be a matter of fewer/missing tracers on the key pad ribbon. The control boards are very similar but there are new or re routed circuits on the board. We're pretty sure you will loose a few selections and display LEDs, but the dishwasher should work satisfactorily in most cases. Read More...
Elisabeth September 08, 2016 for Model Number MDB6701AWB1 All control panel lights work except for the start button. What could be the problem? The dishwasher does not start. Thank you.
1 Answer Hello Elisabeth. Make sure the door switches are good. If so, you will need to replace the control panel 6-919822 on the unit. Read More...
Dale January 25, 2016 for Model Number MDB6601AWB Touch pad just stopped working but rinse light comes on but does nothing .Does this mean control panel is shot?
1 Answer Hello Dale. Based on the information you provided, it sounds like the control panel is bad and will need to be replaced on the unit. Read More...
Bert February 16, 2015 for Model Number MDB6601AWS Think we have several problems. Started with noticing on drying cycle, moisture sometimes leaking out the bottom of the control panel. Also, door latch would not close properly until the handle was squeezed then would push in place to close. Now pushing the buttons and nothing but did see random buttons light up then go out. Control Panel or main board? assuming also, door latch and vent seal?
1 Answer Bert, The issue with the lights coming on then going back out would more likely be caused by a faulty control panel rather than the control board. Read More...
Diana April 23, 2014 for Model Number MDB6601AWQ The first number of the time display only shows half the digit.
1 Answer Hello Diana. You need to order and replace the control panel 6-919822 on the unit. Read More...
Max F April 05, 2014 for Model Number mdb6601awb Does control panel come with handle and latch have two broken supports on plastic panel.
1 Answer Max, The control panel does not come with the latch and handle assembly. The latch assembly is part number WPW10275768 and the handle for the latch is part number WPW10130695. Read More...
Jake March 24, 2014 for Model Number MDB6701AWW2 I lost the memory on one cycle that I used a lot, now I have to use a longer cycle, the model # is 6701AWW2 I am sure I can fix this myself, any suggestions
1 Answer Jake, The most likely cause for the one cycle not to come up is the control panel of the unit being faulty. To replace you would need to turn off the power and remove the screws from the inner door liner. Lift the inner door liner then remove all the parts from the old control panel and install the new one. Read More...
John February 06, 2014 for Model Number Maytag MDB6701AWS The plastic surround for the control panel cracked on top next to the door handle. The machine is working perfectly fine. Can I buy the plastic surround minus the control panel?
1 Answer Hello John! Unfortunately, you'll have to purchase the control panel. The part number is 6-919822. Thanks. Read More...
John S December 20, 2013 for Model Number Maytag series 300 quiet Dishwasher MDB6601AWS How do you install the connector on the ribbon with the control keyboard (AP4364618 (6-919822) PANEL- CON )
1 Answer John, The ribbon harness would just slide straight into the connector on the control board. Read More...