Skip to Content
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Trusted Since 1999 Trusted Since 1999
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google

Customer Questions and Answers for Dishwasher Pump And Motor Assembly by Whirlpool

Best Seller
Manufacturer Part
4.89 (64)
By: Whirlpool
Part Number: OEM17886864
Manufacturer Part Number: W10782773

Fix loud grinding or buzzing noises during wash cycles with this dishwasher pump and motor assembly. Moderately difficult repair, takes 1-2 hours.

More
$180.34

IN STOCK
Ships Today Guaranteed
Add to Cart

Questions & Answers

For Whirlpool Dishwasher Pump And Motor Assembly (Part Number: OEM17886864)

1 Answer

Hello LL. If the chopper was good and clean on the unit, then you will need to replace the circulation pump W10782773 in the unit.

Read More...

1 Answer

Hello Larry,

The first thing a dishwasher does when it's started is try to pump out. If it makes a grinding noise as soon as it's started, there is a foreign object in the pump. If you look at the parts explosion, it's part number 6 on the pump and motor page. It's referred to as a chopper blade and can be accessed from inside the unit without removing the assembly from the unit.
Please check out the attachment. It's a service manual for a dishwasher with the same configuration pump and motor assembly. Look at page 21 of the service manual and it tells how to access the chopper blade. Clear this area and the problem will be solved. The only thing is if it was a piece of glass, this sometimes breaks the shaft that drives the blade W10083957V, so the blade may require replacement.

Read More...

1 Answer

Hello Barbara,

I believe you should check under the float switch and if nothing is under it holding it up so the machine thinks it's full, replace the water inlet valve.

Read More...
Mike for Model Number 66516372300

Our dishwasher is leaking water mostly from bottom of the door. We checked and cleaned the gasket, checked the float switch and then ran the dishwasher wash cycle, stopped it then repositioned wash arms to face the middle of the door. Once we started it back up, the top arm moved, but the bottom arm did not. Would this cause the leak? Would this be an indication for a Circ. Motor and assembly or drain pump? Not really sure where to go from here. Any help would be greatly appreciated

1 Answer

Hi Mike. Remove the lower rack. Wipe off the inner door seal area and inspect for knicks to allow the leak. Inspect the door seal part # [] for any debris allowing it to leak. Remkove the lowe rack and use a torpedo level on the side support rails for front to back level. Some instalers will tilt it slightly 1/4 bubble to the front so it leans baclk slightly if desired. A split middle wash arm will alloww the leak also. Part # []. Use a shop vac and towels to start and inspect from the top down. As yopu inspect the choipper blade see if it has been damaged part # W10083957V. Remove the circulation pump part # WPW10757217. If the impeller is damaged use part # 8193951A. If you need the whole sump assy. it is part # W10782773. Thank You.

Read More...

1 Answer

Rich, the circulation pump and motor assembly W10782773 is the correct assembly replacement used on your Kitchenaid model KUDS01FKPA0. Thanks.

Read More...

1 Answer

Hi ML. You need to use a shop vac to remove the standing water inside the motor/sump area. Use it and towels to clean all wash arms out under the sink. Examine and use a pick tool to dislodge any debris stuck in any wash arm jet holes. Remove the wash arms, racks and the top of the motor area. Clean all down to the chopper blade and let me know what you find..When you have the water out completely and if you have not found anything broken, pull the unit out and remove the motor assy. Check the impeller blade to see if there is anything stuck in it or damaged. Part # 8193951A. Make sure the water delivery manifold is clean. You may be hearing the squeal from the seal assy. I will provide the part #'s needed. Use the supplied tech sheet to put the unit in a field service test. Are there any fault codes ? Make sure the pump is clear and the impeller is not spinning loose on the motor shaft. Thank You.

Read More...

1 Answer

Hello Don. Based on the information you provided, you will need to order W10782773 to replace the sump and motor assembly. Hope this helps.

Read More...

1 Answer

Hello Lisa. See if you can remove the motor W10782773 from the sump. If not, you will need to replace the sump assembly W10782773. Alot of times the chopper and impeller are broken when the motor locks up and it is best to replace the assembly. Hope this helps.

Read More...

1 Answer

Hi Geraldo. Circulation Pump and Motor Assembly Part Number: W10782773. - This dishwasher motor and pump housing assembly includes the smaller 21.06 millimeter port for the thermistor, a sump housing, a motor, the impeller, a shaft seal, a volute and the o-ring seal. Thank You.

Read More...

Have questions? Ask our pros!

Contact us in a way that is convenient for you

Call us 1-877-477-7278
Need Help? Chat with a Pro
Or ask a question by filling in the form

Share your thoughts with other customers

Ask a Question
  • 5,000+ Repair Videos 5,000+ Repair Videos
  • Same-Day Shipping Same-Day Shipping
  • 365 Day Return Policy! 365 Day Return Policy!
  • Repair ForumFree Tech Support!
  • Top Quality Store on Google