William November 24, 2025 for Model Number D7824706Q Ice maker was installed using wiring harness of previous ice maker. It made ice for a while but then stopped. There is ice in the tray but it stopped working. I put an insulated wire in the test holes but no advancement.
1 Answer William, Please resubmit your question with the model number of the refrigerator so that we can assist properly with your question. Read More...
Mike October 08, 2025 for Model Number ET1CHKXKQ00 I'm going to take out my old ice maker and inspect it to see if I need a new one or a new power module. Can I plug the fridge back in and run it after the ice maker is removed?
1 Answer Hello Mike thanks for contacting AppliancePartsPros.com Removing the ice maker will not impact operation of the fridge. Read More...
Mike October 07, 2025 for Model Number Whirlpool Refrigerator, My ice maker makes ice but when I click the bail wire up it doesn't stop making ice. Not sure what to do.
1 Answer Hello Mike, and thank you for your question. It sounds like the ice maker has failed as raising the ice level arm does not stop ice production. Read More...
Terry June 13, 2025 for Model Number RT21LMXK006 Will this replacement ice maker fit and work in my Roper refrigerator
1 Answer Terry, Thank you for your question. The correct icemaker for this unit will be 4317943. Read More...
Jskiff February 01, 2025 for Model Number 106.72159111 Ice maker creates ice but leaks water from both front and back of ice maker into the collection bin creating a huge ice block. It this ice maker or the water inlet valve that has failed?
1 Answer Hello JSkiff, thank you for contacting Appliance Parts Pros. This could be a water valve [WPW10279909] or ice maker [4317943] issue. There is no good way to figure out which it is without replacing at least one of those components. Read More...
Mr. Munro August 22, 2024 Part number AP4135008 (D7824706Q) Ice Maker Adjusting the size of the ice cubes, Removed the cover and found the adjustment. To enlarge the cubes, should I turn it clockwise or counterclockwise. By how much should I turn it?
1 Answer Hello Mr. Munro, thank you for contacting APP, Turning the adjustment screw clockwise decreases the fill amount and counter-clockwise increases the fill amount. This screw will turn one full turn in either direction from the default fill level position. If you are adjusting the fill level you will need to turn that screw in increments, usually about 1/8 to 1/4 turn, and then test the fill amount by activating the icemaker's harvest cycle. Read More...
Ava July 28, 2024 for Model Number MFF2557KES Hi, I have A slow drip leak occurring in the very front of the icemaker. I’m not sure where the leak is coming from but I did make a video which I can send if that will help. There is the same from the front housing to the black plastic and the Leak/drip is in the front by that area. Do you know what could be causing that?
1 Answer Ava, Based on the description of the issue this will likely require a replacement ice maker. Read More...
Jim July 28, 2024 for Model Number ED2FTGXKQ00 Whirlpool When the ice maker fills, the water seems to leak and overfill. The water leaks into the ice cube tray and then we have one big ice cube. Water valve leaking? Thankyou in advance for your help.
1 Answer Hello Jim, thank you for contacting APP, The icemaker leaking and overfilling will be either an issue with the Icemaker 4317943 or the Water Valve W10408179. If the icemaker is immediately leaking after it fills then I would suspect the icemaker as the issue, but it could be either. Read More...
Greg June 17, 2024 for Model Number Amana SCD19JL (P7804508WL) So my ice maker is as pictured in the BOM (part 19 of https://483cda5f439700fab03b-6195bc77e724f6265ff507b1dc015ddb.ssl.cf1.rackcdn.com/0028535618_4.gif ) you show for this model, where the icemaker attaches to the back of the inside of the refrigerator (the length of the icemaker is parallel to the back of the refrigerator, not the left side). Thus the water fill hole is on the back of the right side of the ice maker, not the right side of it, i.e. the fill tube for my old unit would come in perpendicular to the length of the ice maker on the back right side not parallel to it. The picture of the ice maker replacement part Replacement Icemaker D7824706Q / AP4135008, shows the fill hole for a fill tube coming in parallel to the length of the unit. So what is the best way to handle this?
1 Answer Hello Greg, thank you for contacting APP, The Icemaker(IM) D7824706Q should be a direct 1:1 replacement for your original IM, the video attached to D7824706Q is for the front-to-back install instead of the side-to-side install, but these IMs are also known as Modular Icemakers due to the fact they were used across many different units and installed a few different ways, there shouldn't be any issues between the new IM and your unit with the fill tube placement. Read More...
Joe March 23, 2024 for Model Number Part #: AP4135008 (D7824706Q) I replaced the icemake per the video. After the freezer got back down to 10 deg F, I heard the water fill. I could feel water in the tray with my finger. I waited two hours and could feel ice in the tray. The bail arm seems to be moving, but no ice.is being released. What next?
1 Answer Joe, The cycle time is based on the temperature which should be below 8-10°f. Ensure the temperature drops below these temperatures or the ice maker won't cycle. This could be a cooling issue instead of an ice maker issue. Read More...