Andrew January 29, 2023 for Model Number RF111PXSQ3 The Stovetop elements work but the oven bake element does not. Oven Heating light comes on but element has no heat. When setting the dial to Broil High the oven heating light stays on, there is a clicking noise, and the broil element heats up but not to full heat. is this an element issue or a switch issue? Thanks.
1 Answer Andrew, The best option is to check to see if there is 240 vac across the bake element when turned to bake. If there is then the element will be faulty and if there is not then the switch would be the issue. Read More...
Kevin Simmons January 16, 2021 for Model Number WP9762215 oven control switch Whirlpool range in apt. Replaced oven control switch WP9762215 couple years ago got call from tenant oven not work after all simple test found plastic on wiring harness blackened & a little melted switch WP9762215 not working switch not working they are pricey range seems to have some kinda problem cant be 5 6 years old any advice appreciated
1 Answer Kevin S. Based on the information provided it sounds as if you may have had a loose connection which causes heat and burn out. I would replace the switch and repair the wiring and make sure the connectors are on tight. Read More...
Robert May 09, 2018 for Model Number RF110AXSQ3 Had this stove since it was new only issue I have is the big burner on top (left front) no matter what setting I put it it on the burner only goes to high what would cause that.
1 Answer Robert, This issue would most likely be caused by a faulty infinite switch WP3148953. Read More...
Sue P. July 07, 2016 for Model Number GFE461LVS My oven has been thru multiple heating sensors (4), next to last in December due to overheating. I was surprised when I recently had the same issue but thought maybe I got a bad sensor. After just 2 weeks I am back where I started: broiler coming on when oven set to 350°F. Various online info says either control switch, bad connection at main board or main board. How to check to see issue, without purchasing wrong part or buying part and oven not being repair? Thanks
1 Answer Hello Sue, The issue is more likely to be the connection of the temperature sensor to the harness. This connection should be done with ceramic wire nuts and should be outside of the bake compartment insulation. This can be accomplished from inside the bake compartment if the connections are pushed through the insulation and both layers of metal. Read More...
Dustin September 12, 2015 for Model Number whirlpool RF110AXSQ 3 The oven will heat up and the preheat light will go out but it seems to not maintain temperature because the light will come back on every few minutes and it bakes like it never got up to the selected temperature. The broil element has 16 ohms of resistance and the bottom element has 22 ohms. The temperature sensor has 1100 ohms at room temperature. The broil element comes on when set to broil but not when set to bake. The bottom element glows bright red on bake.
Jimmy F April 06, 2014 for Model Number RF110AXSQ I have Whirlpool range, burners work; oven does not. Could it be the switch? Thank you.
1 Answer Jimmy, The switch could be the issue with the unit but you will want to check the thermal cutoff first. If the thermal cutoff 9757158 does not have continuity then it is faulty and would need to be replaced. If the thermal fuse checks ok then the switch WP9762215 would be the issue. Read More...
Danny September 27, 2013 for Model Number rf302bxeno Bottom element and top element are not coming on. replaced both. Elements burn out on a regular basis. Selector knob with temps not letting either element come on. Light for oven is on. Neither one will glow with the bake or broil selection. Are the selector controls bad or it is the thermostat?
1 Answer Danny, The oven selector just determines which one will be allowed to cycle on and off. The oven thermostat 3169307 is the switch that will control the power to the bake or broil. Read More...
Lee January 17, 2013 for Model Number RF111PZSQ3 Oven is not working , when you turn on switch/ temp setting there is no indicator light that oven is on and it makes a constant clicking sound. Neither broiler or bake element heats .
1 Answer Hello Lee, Based on the information it sounds like your oven switch WP9762215 is faulty and would need to be replaced. Read More...
Francisco January 04, 2013 for Model Number Hot Point Electric Stove (I think) with oven switch 9762215 Hot Point Electric Stove (I think) with oven switch 9762215 - Burners are fine. Oven is not working. Very expensive switch. Will like to order one but I will like to troubleshoot first. Switch part number is 9762215. I am good with tools and a multimeter, but dont know the readings I am looking for. This is our small church's stove, used special functions - We don't have much money and will hate for the church to take a $100 hit without making sure.
1 Answer Hello Francisco, I really hate to put off the church, but we really need a model number so we can pull the wiring diagram and give you accurate troubleshooting instruction and readings. If you could check the units' I.D. tag and get back with us we will be more than happy to assist you in the repair. Read More...
Cornelius Woodberry October 19, 2012 for Model Number Amana My stove have completely stopped working. When I turn the stove on and the eye on at the same time all it do is click. So im wondering what the problem might be because the stove is only 1 year old.
1 Answer Hello Cornelius, please provide a complete model number so we know what you are working on. Thanks! Read More...